Megha Satpathy

Dr. Megha Satpathy

Research and Development, Glidewell (United States), Newport Beach, California, USA

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2025 in Dental Materials
Verified
Journal Article
Closed access
MSMegha Satpathy
Megha Satpathy
MLMatthew Loeb
Matthew Loeb
RJRose M. Jose
Rose M. Jose
MSMatthew J. Sinclair
Matthew J. Sinclair
YDYuanyuan Duan
Yuanyuan Duan
JGJason Griggs
Jason Griggs

3 September 2024 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
RTRiya Titus
Riya Titus
MSMegha Satpathy
Megha Satpathy
JMJohn Mecholsky
John Mecholsky
KJKartikeya Jodha
Kartikeya Jodha
NANader Abdulhameed
Nader Abdulhameed
JGJason Griggs
Jason Griggs

21 July 2025 in Materials
Verified
Journal Article
Open access
PDF file
ULUlysses Lenz
Ulysses Lenz
RSRenan dos Santos
Renan dos Santos
MSMegha Satpathy
Megha Satpathy
JGJason Griggs
Jason Griggs
ABAlvaro Della Bona
Alvaro Della Bona
The design of custom abutments (CA) can affect the mechanical reliability of implant-supported restorations. The purpose of the study was to evaluate the influence of design parameters on the fatigue limit of CA and to compare optimized custom designs with the reference abutment (RA). A morse-tapered dental implant, an anatomical abutment, and a connector screw were digitalized using microcomputed tomography. A cone beam computed tomography scan was obtained from one of the authors to virtually place the implant-abutment assembly in the upper central incisor. Ten design parameters were selected according to the structural geometry of the RA and the implant planning. A reverse-engineered RA model was created in SOLIDWORKS and was modified considering a Taguchi orthogonal array to generate 36 CAs with ±20% dimensional variations. Finite element analysis was conducted in ABAQUS, and fatigue limits were estimated using Fe-safe. ANOVA (α = 0.1) identified the most influential parameters. Von Mises stress values ranged from 229 MPa to 302 MPa, and 94.4% of the CAs had a higher fatigue limit than the RA. Three parameters significantly affected the fatigue performance of the implant system. The design process of custom abutments includes critical design parameters that can be optimized for longer lifetimes of implant-abutment restorations.

2 March 2023 in Ceramics
Verified
Journal Article
Open access
PDF file
MSMegha Satpathy
Megha Satpathy
HPHai Pham
Hai Pham
SSShreya Shah
Shreya Shah
This study aimed to investigate four dental adhesive cements and develop a new method for constructing a bi-layered bone holder for implant testing. HahnTM Tapered Titanium Implants (Glidewell Laboratories) were embedded in mono- and bi-layered holders, and the implant components were assembled. First molar zirconia crowns and crowns for the tensile bond strength test were milled and sintered. Three self-adhesive resin cements (SARC) and one resin-modified glass ionomer (RMGI, Glidewell Laboratories) cement were used to cement the crowns on the abutment. Tensile bond strength, compressive load, and oblique load tests were performed on the implants. The Glidewell Experimental SARC (GES, Glidewell Laboratories) and RMGI cements had the highest tensile bond strength after thermocycling. The implant assemblies with these two cements had the highest mean compressive strength after thermocycling. Under oblique load, the implants with Denali (Glidewell Laboratories) and GES had the highest strength before thermocycling. However, after thermocycling, Dencem (Dentex) and RMGI had the highest strength under an oblique load. The GES cement and RMGI cement had a better overall performance with zirconia crowns and titanium abutments. In addition, a novel technique for constructing an artificial, bi-layered bone holder was successfully developed to mimic the natural structure of the jawbone.

17 September 2024 in Computer Methods in Biomechanics and Biomedical Engineering
Verified
Journal Article
Closed access
MSMegha Satpathy
Megha Satpathy
HPHai Pham
Hai Pham
SSShreya Shah
Shreya Shah
This study aimed to evaluate the material properties of four dental cements, analyze the stress distribution on the cement layer under various loading conditions, and perform failure analysis on the fractured specimens retrieved from mechanical tests. Microhardness indentation testing is used to measure material hardness microscopically with a diamond indenter. The hardness and elastic moduli of three self-adhesive resin cements (SARC), namely, DEN CEM (DENTEX, Changchun, China), Denali (Glidewell Laboratories, CA, USA), and Glidewell Experimental SARC (GES-Glidewell Laboratories, CA, USA), and a resin-modified glass ionomer (RMGI-Glidewell Laboratories, CA, USA) cement, were measured using microhardness indentation. These values were used in the subsequent Finite Element Analysis (FEA) to analyze the von Mises stress distribution on the cement layer of a 3D implant model constructed in SOLIDWORKS under different mechanical forces. Failure analysis was performed on the fractured specimens retrieved from prior mechanical tests. All the cements, except Denali, had elastic moduli comparable to dentin (8-15 GPa). RMGI with primer and GES cements exhibited the lowest von Mises stresses under tensile and compressive loads. Stress distribution under tensile and compressive loads correlated well with experimental tests, unlike oblique loads. Failure analysis revealed that damages on the abutment and screw vary significantly with loading direction. GES and RMGI cement with primer (Glidewell Laboratories, CA, USA) may be suitable options for cement-retained zirconia crowns on titanium abutments. Adding fillets to the screw thread crests can potentially reduce the extent of the damage under load.

11 March 2022 in Dental Materials
Verified
Journal Article
Closed access
MSMegha Satpathy
Megha Satpathy
RJR.M. Jose
R.M. Jose
MSM.J. Sinclair
M.J. Sinclair
YDY. Duan
Y. Duan
ABAlvaro Della Bona
Alvaro Della Bona
JGJason Griggs
Jason Griggs