Kai Li

Dr. Kai Li


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 March 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
HSHongwei Shi
Hongwei Shi
KLKai Li
Kai Li
FLFeng Li
Feng Li
JMJianxing Ma
Jianxing Ma
YTYubing Tu
Yubing Tu
Lei ShanLei Shan
Lei Shan
BiFeO3–based ceramics possess an advantage over large spontaneous polarization and high Curie temperature, and are thus widely explored in the field of high–temperature lead–free piezoelectrics and actuators. However, poor piezoelectricity/resistivity and thermal stability of electrostrain make them less competitive. To address this problem, (1 − x) (0.65BiFeO3–0.35BaTiO3)–xLa0.5Na0.5TiO3 (BF–BT–xLNT) systems are designed in this work. It is found that piezoelectricity is significantly improved with LNT addition, which is contributed by the phase boundary effect of rhombohedral and pseudocubic phase coexistence. The small–signal and large–signal piezoelectric coefficient (d33 and d33*) peaks at x = 0.02 with 97 pC/N and 303 pm/V, respectively. The relaxor property and resistivity are enhanced as well. This is verified by Rietveld refinement, dielectric/impedance spectroscopy and piezoelectric force microscopy (PFM) technique. Interestingly, a good thermal stability of electrostrain is obtained at x = 0.04 composition with fluctuation η = 31% (Smax'−SRTSRT×100%), in a wide temperature range of 25–180 °C, which is considered as a compromise of negative temperature dependent electrostrain for relaxors and the positive one for ferroelectric matrix. This work provides an implication for designing high–temperature piezoelectrics and stable electrostrain materials.

23 March 2022 in Materials Letters
Verified
Journal Article
Closed access
KLKai Li
Kai Li
SCShan Cong
Shan Cong
HZHuashan Zheng
Huashan Zheng
TWTing Wang
Ting Wang
ZZZhenting Zhao
Zhenting Zhao
WGWeiping Gong
Weiping Gong

24 September 2026 in Nanomaterials
Verified
Journal Article
Open access
PDF file
HMHaijuan Mei
Haijuan Mei
RWRui Wang
Rui Wang
LGLibin Gan
Libin Gan
LCLixia Cheng
Lixia Cheng
YSYouqu Shen
Youqu Shen
DGDongsen Geng
Dongsen Geng
The TiAlMoN coatings were deposited by arc ion plating under different substrate bias voltages, and the effects of substrate bias on the composition, phase structure, microstructure, and mechanical properties of the coatings were systematically investigated. The results showed that, as the bias voltage increased from 0 V to −75 V, enhanced ion bombardment promoted coating densification, the N/(Ti + Al + Mo) atomic ratio decreased from 1.33 to 1.05, and the deposition rate increased from 124.7 nm/min to 138.2 nm/min. XRD peak fitting revealed that the TiAlMoN coatings may consist of three phases: c-TiN, fcc Mo-N, and c-AlN. With increasing negative bias voltage, the preferred (111) orientation became more pronounced, while the Mo-N phase gradually evolved from B1-MoN to γ-Mo2N. As the substrate bias voltage increased, the grain size initially reduced and then slightly increased, and the compressive residual stress sharply increased from 0.68 GPa to 2.21 GPa. Owing to coating densification, grain refinement, and increased compressive residual stress, the hardness increased from 16.7 GPa to 33.9 GPa. The adhesion strength reached a maximum of 59.7 N at −25 V and decreased at higher bias voltages because of excessive residual stress. Appropriate control of the substrate bias voltage enables the synergistic optimization of structural strengthening and interfacial stability in TiAlMoN coatings.