Fortification structures, both military and civilian, are designed to resist a blast explosion to some extent. Their technical condition after a blast load must be assessed in a fast and reliable way to enable the users’ decision about the future use of the structure. Preferably, for the assessment of the protective structure, the non-destructive testing method should be used. To assess the suitability of ultrasound testing method for fortification structures built from steel fiber reinforced concrete, an investigation in a laboratory and in situ was conducted, together with numerical simulation and statistical evaluation. The numerical simulation of the blast load of a steel fiber reinforced concrete slab was conducted using multiphysics simulation software with the aim to verify basic parameters of the field experiment. During the field tests, several slabs were loaded by plastic explosive and changes in the structure of the slabs, before and after the blast load, were examined using the ultrasound pass-through method. After the field tests, the slabs were subjected to a destructive laboratory test to determine their residual strength. Subsequently, the data sets obtained from the measurements were tested using functional data analysis. The results from the ultrasound pulse method show that specimens after a dynamic blast load can in some cases increase the strength of their cement matrix.

The reliability of numerical simulations of the structural response of nonhomogeneous materials to high velocity loadings is highly dependent on the used material model and parameters. For nonhomogeneous materials, such as fibres, reinforced concrete is widely used for the Winfrith model, but the question of appropriate material parameters for Ultra-High Performance Fibre Reinforcement Concrete (UHPFRC) under high velocity loadings is still open. The article deals with possible method of inverse identification of material parameters of a UHPFRC slab under blast loading for a Winfrith material model. Possible application is in the field of numerical simulation of protective or critical infrastructure response to blast loading. Experimental measurement of the time–deflection curve through laser scanning using the triangulation method gave us input data for an inverse identification phase conducted in Optislang software. Obtained material parameters from a given range are optimized for blast loading and their Pearson’s correlation coefficient provides us information about their significance for simulation.

Plastic spacers create a linear and systemic weakening of the structure. The extreme loading of the structure tests the structure itself to its load-bearing limit or even locally exceeds this limit, thus revealing all its weak points, which are the spacers. Nevertheless, the influence of the spacers is not included in the design calculation of the reinforced concrete element. In addition, products intended as spacers for the placement of reinforcement do not belong to the specific families of construction products covered by a harmonized standard of European parliament regulation. For these reasons, it is not required to demonstrate any characteristics of these products. This fact allows the use of arbitrary spacers’ shapes and materials. As shown by the experiment carried out, the use of commonly used plastic liners will result in a weakening of the cross-section. The normal assessment of the ultimate or serviceability limit state is not affected by this weakening. An example of an experiment carried out where this problem was captured is the subject of this paper. With Europe’s current deteriorated safety situation, understanding the influence of spacers in blast-loaded reinforced concrete structures on structural failure is important, and it is appropriate to further address this issue. Based on this experiment, it is not possible to accurately identify the causes of the explosion cracks. In order to determine with certainty the effect of spacers on the strength of the structure under abnormal blast loadings, research needs to focus on this area. In the field experimental measurements and numerical simulations, it was found that the use of linear spacers has an effect on crack formation under the blast action of the tested slab.

Deep sea nodules are considered as an alternative and very rich source of several metals. Up to pre-sent days, the processing of these polymetallic ores is cosidered to be carried out by the extraction of individual metals. This work deals wit...

The topic of energy use and energy consumption is currently largely dealt not only in the architecture and civil engineering but also in the military environment. The operating costs of military camps and facilities can be rising extremely quickly especially in hot climate conditions where the requirements for appropriately air-conditioned working places and other mission related areas are crucial for the uninterrupted command and control of any operation. The energy use and energy consumption must be considered already during the planning phase of the military facility and it must take into account as many limiting factors as possible. This is not a completely new problem and many different approaches to the solution are already here and ready to use, and one of them is a method or a system called energy audit that is an efficient tool for improving the energy use and consumption.