Shumei Lou

Prof. Shumei Lou


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 August 2020 in Materials
Verified
Journal Article
Open access
PDF file
SLShumei Lou
Shumei Lou
CQChuan Dong Qu
Chuan Dong Qu
GGGuang Xin Guo
Guang Xin Guo
LRLing Wei Ran
Ling Wei Ran
YLYong Qiang Liu
Yong Qiang Liu
Qingbiao WangQingbiao Wang
Qingbiao Wang
Aluminum composites reinforced by graphene nanoplates(GNP) with a mass fraction of 0.5% (0.5 wt.% GNP/Al) were fabricated using cold pressing and hot pressing. An orthogonal test was used to optimize the fabrication parameters. Ball milling time, ball milling speed, and ultrasonic time have the largest influence on the uniformity of the graphene in the composites. Afterwards, the microstructure, interfacial properties, and fracture morphology of the composites obtained with different parameters were further analyzed. The results show that ball milling time and ball milling speed have obvious influences on the mechanical properties of the composite. In this paper, when the ball milling speed is 300 r/min and the ball milling time is 6 h, the dispersion uniformity of graphene in the 0.5 wt.% GNP/Al composite is the best, the agglomeration is the lowest, and the mechanical properties of the composites are the best, among which the tensile strength is 156.8 MPa, 56.6% higher than that of pure aluminum fabricated by the same process (100.1 MPa), and the elongation is 19.9%, 39.8% lower than that of pure aluminum (33.1%).

7 October 2022 in Fibers and Polymers
Verified
Journal Article
Closed access
PDF file
SLShumei Lou
Shumei Lou
GRGuodong Ren
Guodong Ren
HZHui Zhang
Hui Zhang
BCBaojia Cheng
Baojia Cheng
PCPeng Chen
Peng Chen

28 February 2021 in Materials
Verified
Journal Article
Open access
PDF file
Qingbiao WangQingbiao Wang
Qingbiao Wang
HSHongxu Song
Hongxu Song
YLYue Li
Yue Li
FWFuqiang Wang
Fuqiang Wang
ZHZhongjing Hu
Zhongjing Hu
Zhenyue ShiZhenyue Shi
Zhenyue Shi
An important way to improve concrete performance is the use of alkali-resistant glass fibers (ARGFs) as reinforcement. This paper is based on the problems of the cracking of the partition wall and lining seepage in Laoshan Tunnel, Qingdao, China. Two types of ARGFs were selected as reinforcement materials for the partition wall and lining concrete: high dispersion (HD) and high performance (HP); and the compressive strength (CS), tensile strength (TS), flexural strength (FS), and impervious performance (IP) of concrete with different gradations of the two types of fibers were investigated. The results show that although the CS of graded glass fiber reinforced concrete (G-GRC) is slightly decreased, the TS, FS, and IP of G-GRC are significantly improved. When the densities of the ARGFs of HD and HP are 0.6 and 5 kg/m3, respectively, G-GRC performs best; additionally, compared with ordinary concrete, the TS, FS, and IP of G-GRC are increased by 15.86%, 14.90%, and 31.58%, respectively. Meanwhile, the tension–compression ratio is increased by 22.29%, and the mechanical properties of concrete are remarkably enhanced. The research results were successfully applied to the construction of the Laoshan tunnel, and good engineering results were obtained.

30 June 2020 in Journal of Wuhan University of Technology-Mater. Sci. Ed.
Verified
Journal Article
Closed access
PDF file
SLShumei Lou
Shumei Lou
WYWenying Yin
Wenying Yin
XMXiaodong Ma
Xiaodong Ma
JYJianjun Yuan
Jianjun Yuan
QWQingBiao Wang
QingBiao Wang

1 January 2021 in Science and Engineering of Composite Materials
Verified
Journal Article
Open access
PDF file
SLShumei Lou
Shumei Lou
HZHui Zhang
Hui Zhang
FLFang Liu
Fang Liu
JWJianchao Wang
Jianchao Wang
WYWenying Yin
Wenying Yin
CSChunjian Su
Chunjian Su
A plate used in a medium voltage switch, made by a 25 wt% glass fiber-reinforced polyamide 66 composite filled with flame-retardant red phosphorus (RP) (PA66-GF25 FR (RP)), was injection molded. To satisfy the relatively high dimensional accuracy requirement, a “supporting mold” was used to compensate for the difference between the transverse and longitudinal linear shrinkage of the PA66-GF25 FR (RP). To reduce the internal residual stress caused by the “supporting mold,” hygrothermal conditioning treatments, including boiling water bath at 90–100°C and re-drying at 110°C, were used. To determine the effects of boiling water bath and re-drying on the dimensional accuracy and mechanical properties of the product, three treatment routes were applied. It was found that the route in which the boiling water bath is applied after the “supporting mold” is preferred to ensure the dimensional accuracies and the mechanical properties as a whole. Using a boiling water bath as a hygrothermal conditioning treatment can improve the mechanical properties and increase the dimensional accuracy of the product. In addition, by using the preferred route, re-drying can further improve the tensile, bending, and even impact strength.

4 April 2019 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
SLShumei Lou
Shumei Lou
AWAnning Wang
Anning Wang
SLShuai Lu
Shuai Lu
GGGuangxin Guo
Guangxin Guo
CQChuandong Qu
Chuandong Qu
CSChunjian Su
Chunjian Su