The purpose of this study was to evaluate the chemical and mechanical modifications in subsurface dentin layer after Er: YAG (Erbium-Yttrium Aluminium Garnet) laser irradiation, as the guidance of new dental restorative materials specific for laser irradiated dentin. Dentin disks obtained from extracted human molars were prepared and exposed to a single pulse Er:YAG laser irradiation at 80mJ/pulse. After laser irradiation the mechanical and chemical characteristics of intertubular dentin in subsurface layer were studied using nanoindentation tester and micro-Raman spectromy (μ-RS). The dentin 5-50µm depth beneath the lased surface was determined as testing area. Two-way analysis of variance (ANOVA) were used to compare the mechanical values between lased and untreated subsurface dentin (P = 0.05). A laser affected subsurface dentin layer after Er:YAG laser treatment is present. The laser irradiation is considered to decrease the mechanical properties in the superficial subsurface layer ( 0.05) under the depth of 15µm. However, the dentin at 5µm and 10µm depth beneath the lased surface exhibited significantly lower (~ 47.8% and ~ 33.6% respectively) hardness (p < 0.05). Er:YAG laser irradiation affected both mineral and organic components in subsurface dentin layer, a higher degree of crystallinity and reduced organic compounds occurred in the lased subsurface dentin. Under the tested laser parameters, Er:YAG laser irradiation causes lower mechanical values and reduction of organic components in subsurface dentin, which has deleterious effects on resin adhesion to this area.
19 February 2019 in Clinical and Experimental Dental Research
The purpose of this study was to evaluate the effect of pH conditioners on tooth bleaching using hematoporphirin‐stained paper and artificially discolored bovine tooth model. Experimental bleaching gels containing 23% hydrogen peroxide, adjusting pH 7.0 by different pH conditioners (NaOH, NaHCO3, Na2CO3, KOH, KHCO3, and K2CO3), were prepared. Each bleaching gel was applied on a hematoporphirin‐stained paper, and the light was exposed for 5 min. Before and after bleaching, color was measured and color difference was calculated. Artificially discolored bovine tooth samples were prepared and bleached by four experimental bleaching gels containing NaOH, NaHCO3, Na2CO3, or KHCO3. The bleaching time was 10 min with light exposure, and bleaching was repeated 10 times. The color of bleached surface was measured at each bleaching period, and color difference was calculated. In the experiment using hematoporphirin‐stained paper, degrees of color difference were KHCO3 > NaHCO3 > KOH > NaOH > Na2CO3 ≥ K2CO3. In the experiment using bovine teeth, degrees of color difference were KHCO3 > NaHCO3 > NaOH > Na2CO3. It was concluded that the bleaching materials with same pH and different pH conditioners showed different bleaching effects and that both cation and anion in the pH conditioners affected bleaching effect.
1 November 2012 in Photomedicine and Laser Surgery
Objective: The objective of this study was to evaluate the effects of a 405 nm diode laser on bleaching reaction of H 2 O 2 and VL-TiO 2 on methylene blue (MB) dye. Background data: Visible light activating titanium dioxide photocatalyst (VL-TiO 2 ) may improve efficacy of hydrogen peroxide (H 2 O 2 ) bleaching agents used in dentistry while contributing to their safety by lowering the required concentration of peroxide. Methods: The experimental solution was prepared with H 2 O 2 , VL-TiO 2 , MB, and pure water. The final concentration of H 2 O 2 was 3.5% and that of MB was 10 ppm. The experimental solution of 3 mL in a quartz cell was irradiated by a 405 nm diode laser with various powers, duty cycles, and pulse durations for 7 min. Results: In all irradiation conditions, the increase in laser irradiation time gradually decreased the MB concentration. Irradiation by higher output power showed more reduction of MB concentration. Pulse durations as short as 5 ms with duty cycle reduced to 25% did not affect the degree of the reduction in MB concentration compared with continuous wave irradiation at the same average output power. Conclusions: It was concluded that using 405 nm diode laser, the bleaching effects of VL-TiO 2 depended upon the irradiation time and the average output power, regardless of pulse duration or duty cycle.
This study evaluated the alterations of surface topography of the bovine enamel caused by different pH of in-office bleaching agents. 23% H2O2 with pH 5.5, 7.0 and 8.5 were applied on the bovine tooth specimens (n=10) and photo-irradiated for 10 min. The bleaching procedure was repeated three times and specimens were subjected to linear surface roughness (Ra) and Vickers microhardness test (VHN) at baseline and after three consecutive applications. The morphological alterations were observed before and after third bleaching application. Data were analyzed by two-way ANOVA followed by Tukey’s HSD. The pH of the bleaching agent significantly affects the Ra and VHN (p<0.05). Low pH yielded a significant increase in Ra and decrease in VHN. All the groups showed morphological alterations and profound effect was found in pH 5.5 group. It was concluded that the pH of the bleaching agent can affect Ra, VHN and surface morphology.
1 August 2015 in Journal of the Mechanical Behavior of Biomedical Materials