Ahmed Shakir Al-Hiti

Dr. Ahmed Shakir Al-Hiti


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2019 in Optical Fiber Technology
Verified
Journal Article
Closed access
SSSameer Salam
Sameer Salam
AAAhmed Shakir Al-Hiti
Ahmed Shakir Al-Hiti
AAAb.H.H. Al-Masoodi
Ab.H.H. Al-Masoodi
PWPengfei Wang
Pengfei Wang
WWWei Ru Wong
Wei Ru Wong
SHS.W. Harun
S.W. Harun

18 September 2020 in IEEE Access
Verified
Journal Article
Open access
Mahmood A. Al-ShareedaMahmood A. Al-Shareeda
Mahmood A. Al-Shareeda
MAMohammed Anbar
Mohammed Anbar
MAMurtadha Ali Alazzawi
Murtadha Ali Alazzawi
SMSelvakumar Manickam
Selvakumar Manickam
AAAhmed Shakir Al-Hiti
Ahmed Shakir Al-Hiti
Recently, Vehicle Ad Hoc Networks (VANETs) have been increasingly developed in Intelligent Transportation Systems (ITSs). However, VANETs are vulnerable to security issues because of the open-medium nature of Vehicle-To-Vehicle (V2V) and Vehicle-To-Infrastructure (V2I) communication. Recently, many studies have proposed security schemes to address these issues. However, many of these schemes have massive computational overheads, especially in the process of batch verification method, which verifies multiple messages simultaneously. In this paper, a Lightweight Security Without Using Batch Verification Method (LSWBVM) scheme is proposed based on Elliptic Curve Cryptography (ECC). The proposed LSWBVM scheme uses the XOR operation and general hash function during mutual authentication. Meanwhile, to verify a large number of messages, the proposed scheme uses an efficient single verification instead of batch verification in a high traffic density-area. BAN logic proves that the LSWBVM achieves the security goals to mutually authenticate between the nodes. The security analysis indicates that the LSWBVM satisfies the security requirements, such as: identity privacy preserving, tractability and revocability; and secure non-forgery under the random oracle model in an adaptively chosen message attack. The preference evaluation shows that the single verification of proposed LSWBVM is more efficient when compared with batch verification of the related works.

4 February 2020 in Journal of Modern Optics
Verified
Journal Article
Closed access
AAAhmed Shakir Al-Hiti
Ahmed Shakir Al-Hiti
AAA. H. H. Al-Masoodi
A. H. H. Al-Masoodi
HAH. Arof
H. Arof
WWWei Ru Wong
Wei Ru Wong
S. W. HarunS. W. Harun
S. W. Harun
This paper reports a new type of passive saturable absorber (SA) made of transition metal oxide (TMO) embedded in polyvinyl alcohol (PVA). The Tungsten trioxide (WO3)-PVA SA is placed in an erbium-doped fibre laser cavity to produce Q-switched pulses operating at 1562.82 nm. The pulse laser starts to manifest at the threshold pump power of 40 mW and continues to exist until the maximum pump power of 195 mW. Within that pump power range, its pulse energy, repetition rate and pulse width vary from 98 to 142.85 nJ, 29.86 to 56.7 kHz and 5.032 to 1.85 µs, respectively. The pulse train is stable with a signal to noise ratio of 70 dB. This is the first demonstration of a Q-switched laser using such a SA.

1 April 2021 in Optik
Verified
Journal Article
Closed access
AAAhmed Shakir Al-Hiti
Ahmed Shakir Al-Hiti
AAAhmed H.H. Al-Masoodi
Ahmed H.H. Al-Masoodi
MNMustafa Mohammed Najm
Mustafa Mohammed Najm
MYMoh. Yasin
Moh. Yasin
S. W. HarunS. W. Harun
S. W. Harun

1 October 2020 in IET Optoelectronics
Verified
Journal Article
Open access
PDF file
AAAhmed Shakir Al-Hiti
Ahmed Shakir Al-Hiti
AAAhmed Shakir Al-Hiti
Ahmed Shakir Al-Hiti
Wei Ru WongWei Ru Wong
Wei Ru Wong
SHSulaiman Wadi Harun
Sulaiman Wadi Harun
This study experimentally demonstrates a Q‐switched fibre laser using a new tungsten tri‐oxide (WO 3 )‐based saturable absorber (SA). Using the drop and casting approach, we managed to prepare a thin film that contained WO 3 powders in polyvinyl alcohol. A small bit of the film was used to form an SA which was placed in a ytterbium‐doped fibre laser cavity to generate a Q‐switched laser. The laser, operating at 1063.78 nm, was realised at the threshold pump power of 85 mW with a repetition rate of 23.87 kHz and a pulse width of 5.56 μs. At the pump power of 147 mW, the laser produced the maximum pulse energy of 625 nJ, signal‐to‐noise ratio of 59 dB, the repetition rate of 39.79 kHz and pulse width of 2.37 μs. To the best of our knowledge, this is the first demonstration of using WO 3 SA to generate the pulse laser in the 1 μm region.

11 July 2025 in Journal of Umm Al-Qura University for Engineering and Architecture
Verified
Journal Article
Open access
PDF file
AAAhmed Shakir Al-Hiti
Ahmed Shakir Al-Hiti
AAAbdullah Khalid Ahmed
Abdullah Khalid Ahmed
SMShahad Hussam Mhmood
Shahad Hussam Mhmood
BHBashayer Ismail Hamdallah
Bashayer Ismail Hamdallah
In this paper, we propose and evaluate two novel millimeter-wave (mmWave) microstrip patch antenna designs for advanced 5G applications. These antennas are engineered for compact size and broadband performance, utilizing low-cost Rogers (RO4450B) substrates. The first antenna demonstrates a multiband response with resonances at 29.26 GHz, 114.55 GHz, and 138.76 GHz, achieving a maximum efficiency of 94%. The second antenna achieves both broadband and multiband operation across frequencies from 30.63 to 335.5 GHz, with six operating bands and return losses below − 10 dB, including a peak of − 22.56 dB. Both designs are modeled and analyzed using CST Microwave Studio and are particularly suitable for high-capacity mmWave wireless systems. Key performance metrics include gain, VSWR, return loss, power loss, and radiation characteristics. This work provides insight into the application of patch modifications and feed optimization for next-generation high-frequency communications. The radiation characteristics of the proposed antennas support high directivity and stable main lobes, which are essential for beamforming and multibeam configurations in 5G systems. Although the designs do not use active beam steering circuits, their compatibility with phased array integration makes them suitable for directional transmission and reception in mmWave applications. Multiband behavior arises due to resonance in multiple slot-created current paths, where each slot adds or perturbs a mode with a distinct electrical length. These additional paths produce resonant conditions at different frequencies, enabling discrete multiband operation. The layout symmetry and via-loaded substrate further stabilize the impedance at higher bands.