Hein Zaw Oo

Dr. Hein Zaw Oo

Department of Mining and Materials Engineering, Prince of Songkla University, Hat Yai, Songkhla, Thailand
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2024 in Materials Research Express
Verified
Journal Article
Open access
RBRomadorn Burapa
Romadorn Burapa
Hein Zaw OoHein Zaw Oo
Hein Zaw Oo
WSWissarut Sangwiman
Wissarut Sangwiman
PMPrapas Muangjunburee
Prapas Muangjunburee
The major goal of this study is to enhance the mechanical and metallurgical characteristics of rail steel grade R260 joined by thermite welding under various preheating conditions, including preheating time and gas pressure. Mainly two conditions, referred to as the Normal Condition and Improved Condition, are carried out for experiments. Prior to welding, the Normal Condition was preheated using liquefied petroleum gas (LPG) and oxygen gas pressures of 1 bar and 4.5 bar for 3 min, and the Improved Condition was preheated using liquefied petroleum gas and oxygen gas pressures of 1.2 bar and 4.5 bar for 6 min and 30 s. To investigate the mechanical and physical properties, micro-Vickers hardness tests, tensile tests and slow bending tests were also carried out. Welded metal in Normal Condition has many defects, including gas holes and shrinkage cavities. When comparing the Normal Condition to the Improved Condition, the Improved Condition demonstrates significantly more bending load and deflection. Specifically, the thermite welded rail sample of Improved Condition demonstrated a remarkable ability to endure bending loads of 108 tonnes and a deflection of 16 mm, and this sample remained unbroken until it exceeded 50% of the standardized deflection limit (10 mm). In addition, the average hardness values for the Improved Condition of the weld metal zone and the heat-affected zone were 331 HV and 289 HV, respectively. The Normal Condition produced an unsatisfactory fracture surface after slow bending test. This was caused by weld defects at the thermite weld due to inappropriate preheating.

1 August 2024 in Materials Research Express
Verified
Journal Article
Open access
PSPorntep Sareekumtorn
Porntep Sareekumtorn
SCSasirat Chaideesungnoen
Sasirat Chaideesungnoen
PMPrapas Muangjunburee
Prapas Muangjunburee
Hein Zaw OoHein Zaw Oo
Hein Zaw Oo
This research investigated the corrosion behavior of standard current metal inert gas weld repair for 6082-T6 aluminum alloy using ER5356 filler metal. The new and repaired (NW and RW) welds were studied. The welds comprised the weld metal (WM), the heat affected zone (HAZ) (solid solution and softened zones), and the base metal (BM). The study focused on investigating electrochemical corrosion using polarization and electrochemical impedance spectroscopy (EIS) methods in 3.5% NaCl solutions, especially in HAZ, including metallurgical and mechanical examinations. The BM containing an α-Al matrix with Al(Fe,Mn)Si and Mg2Si phases exhibited the maximum hardness (70–104 HV0.1). The WM hardness decreased (67–76 HV0.1) with the α-Al, β-Mg3Al2, and Mg2Si phases. Despite having comparable phases to BM, HAZs showed lower hardness (Solid HAZ: 70–82 HV0.1) due to more intermetallic phases. The RW’s softened HAZ revealed the minimum hardness (52–63 HV0.1) compared to that of the NW (55–70 HV0.1). Besides, the tensile strength of the RW (179.7 MPa) was also lower than that of the NW (174.4 MPa) because of the reheating effect. The electrochemical corrosion results indicated that the BM exhibited the maximum corrosion resistance (the lowest corrosion current density (icorr), the highest corrosion potential (Ecorr), and the charge transfer resistance (Rct)), followed by the HAZ and the WM, respectively. The softened HAZ demonstrated better corrosion resistance than the solid solution HAZ. Conversely, the over-aging effect reduced the softened zone’s pitting corrosion resistance (Ep) compared to the solid solution zone. The RW exhibited inferior corrosion resistance compared to the NW due to increased intermetallic phases, which was consistent with the mechanical results. However, the RW’s softened HAZ corrosion characteristics were inconsistent with its mechanical properties; its hardness and tensile strength were the lowest, but its corrosion resistance was not. Pitting corrosion was observed on the weld surfaces using the SEM.

1 June 2020 in Surface Topography: Metrology and Properties
Verified
Journal Article
Closed access
PDF file
BSBuntoeng Srikarun
Buntoeng Srikarun
Hein Zaw OoHein Zaw Oo
Hein Zaw Oo
PMPrapas Muangjunburee
Prapas Muangjunburee
Selecting welding consumables to get satisfactory results in hard facing weld repair jobs at a low cost is an important consideration. The standard martensitic welding electrodes used for hardfacing are expensive, so an investigation into finding suitable substitutes is a worthwhile activity. The objective of this study was to analyze the hardfacing deposits on using a low carbon steel welding electrode with metal powders added to the weld pool. Four different samples were hardfaced applying a submerged arc welding setup with constant heat input. Single and three layers of hardfacing samples were welded using a standard martensitic electrode and compared to using low carbon steel electrodes with added metal powders. An optical emission spectrometer was used to obtain the chemical compositions of welded metal layers. A scanning electron microscope was used to characterize the metallurgical structures of deposits. SEM images of worn surfaces were also obtained. Microhardnessand abrasive testing were used to examine the mechanical properties of the hardfaced surfaces. The results showed that martensitic microstructures were obtained in the hardfaced deposits using a low carbon steel welding electrode with added metal powders. However, hardness and abrasive wear resistance of both single and three layers of hardfacing using low carbon steel welding electrode with added metal powder were below those achieved by welding with a standard martensitic electrode.

25 July 2019 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
Hein Zaw OoHein Zaw Oo
Hein Zaw Oo
BSBuntoeng Srikarun
Buntoeng Srikarun
PMPrapas Muangjunburee
Prapas Muangjunburee
In this research, four samples of 3.5% Cr steel plates were hardfaced using austenitic stainless-steel buffer electrodes and martensitic steel hardfacing electrodes with a submerged arc welding process. This research seeks to the optimum welding parameters to get maximum wear resistance in the hardfaced layer. Heat inputs of 15 kJ/cm to 18 kJ/cm and Direct Current Electrode Positive (DC+) and Alternating Current Electrode (AC) welding polarities were applied. The microstructural analysis was conducted using an optical microscope (OM) and a scanning electron microscope (SEM). Microhardness values of the hardfaced samples were obtained using a Vickers hardness tester, and abrasive wear mass loss was measured using a dry sand rubber wheel apparatus, following ASTM G65 A standard. It was seen that the hardness profiles across the cross-section of the top hardfaced layer and along the top surface were different. The microstructure in the deposited layers, especially the quantity of martensite phase played a major influence on the wear resistance. Hardfaced layers applied with low heat input showed the highest amount of martensite phase and lowest abrasive mass loss. The hardfaced layers using AC polarity contained higher amount of martensite and lower abrasive mass loss than the layers applied using DC+ polarity.

1 February 2026 in Engineering Research Express
Verified
Journal Article
Closed access
JCJanetira Chankaew
Janetira Chankaew
SCSasirat Chaideesungnoen
Sasirat Chaideesungnoen
PMPrapas Muangjunburee
Prapas Muangjunburee
Hein Zaw OoHein Zaw Oo
Hein Zaw Oo
This research examines the microstructural evolution of Inconel 625 (nickel-based superalloy) laser-cladded onto a 2.25Cr-1Mo steel substrate (low-alloy steel) for the steam turbine rotor restoration, exposed to post-weld heat treatment (PWHT) at 690 °C for 0 (as-cladded), 1, 2, and 4 h. Scanning electron microscopy with energy-dispersive x-ray spectroscopy (SEM/EDS), x-ray diffraction (XRD) analysis, and microhardness tests were used to assess the clad characteristics. Results indicated that prolonged PWHT duration led to a reduction in the hardness of the 2.25Cr-1Mo steel heat-affected zone (HAZ) (from 296.6 ± 11.9 to 187.8 ± 3.5 HV 0.2 ), while simultaneously increasing the Inconel 625 clad hardness (from 271.5 ± 3.4 to 287.6 ± 5.0 HV 0.2 ). Following PWHT, the bainitic HAZ converted into tempered bainite; conversely, the clad layer, mostly consisting of an austenitic phase, provided increased precipitation of secondary phases. Further microstructural analysis of the clad layer proved that the as-cladded condition included an austenitic matrix and an intermetallic phase, identified as carbides enriched with carbon (C), niobium (Nb), and molybdenum (Mo). PWHT promoted the precipitation of Nb/Mo-rich carbides within the face-centered cubic (FCC) austenitic matrix. Quantitative XRD investigation revealed a significant reduction in the austenite lattice parameter ( a ), reaching a minimum after 4 h (from 3.5954 to 3.5895 Å). This crystallographic shrinkage offers visible evidence of solute depletion, as Nb and Mo atoms migrate from the solid solution to form secondary phases. These findings suggest that precipitation hardening, influenced by carbide kinetics, is the primary process responsible for the enhancement of the clad’s mechanical properties.

20 September 2026 in Journal of Engineering Research
Verified
Journal Article
Open access
ATAnuchit Teherng
Anuchit Teherng
Hein Zaw OoHein Zaw Oo
Hein Zaw Oo
PMPrapas Muangjunburee
Prapas Muangjunburee