With the need for specialized civil engineers rising in local and regional markets, Al-Zaytoonah University of Jordan (ZUJ) had launched the Civil and Infrastructure Engineering (CIE) program in 2009. The CIE program has aspired to be among renowned universities worldwide through the recognition of the Accreditation Board for Engineering and Technology (ABET). The CIE curriculum was adapted to meet the requirements of ABET. As a consequence of preparing for the first-time accreditation of the CIE program, the authors have learned several valuable lessons. This article constitutes a roadmap to those seeking first-time ABET (or other) engineering accreditation for their programs by reviewing the work of other successful first-time accreditation efforts and analyzing similar processes that were necessitated at ZUJ in preparation for the accreditation. In particular, the article describes the processes used and corresponding results of the ABET Site Visit completed in November and provides a good resource for conducting a sustainable continuous improvement process. Throughout the self-assessment process, feedback was gathered and information was solicited from internal and external formal/informal sources. Periodic collections of specific inputs regarding the program educational objectives, curriculum, and outcomes were requested through meetings, discussions, questionnaires and archives of the CIE Department in the period from 2016 to 2019. Data analysis was performed using Likert scale, statistical analysis, qualitative analysis and judgment to evaluate and perform the necessary reviews and revisions in the accreditation process.
This paper is an experimental study of the effectiveness of using internal and external alkali-resistant glass fabric textile (AR-GT) layers for flexural strengthening of reinforced concrete (RC) beams. The experimental work compares internal single and triple layers of AR-GT as supplemental flexural reinforcement with textile-reinforced mortar (TRM) in RC beams subjected to four-point bending loading. In addition, a control beam specimen is cast with no AR-GT fabric. Monitoring the load–deflection curves, crack patterns, and strengthening layer performance showed that using AR-GT for internal and external layers increased the load-carrying capacity of RC beams. The failure patterns of beams with one external AR-GT layer and three internal AR-GT layers showed a similar trend, with higher loading capacity and lower deflections than the other beams. Three internal textile AR-GT layers recorded higher flexural strength (52%) than one internal layer (6.3%), compared to the control beam specimen. Moreover, using one layer of external AR-GT fabric exhibited higher flexural strength than using one or three internal layers (56.8%).
Mixing cement with water in mass concrete production is associated with hydration heat generation, which may cause concrete mixes to dry out and crack. The experimental work aims to evaluate the effects of using liquid nitrogen (LN) in cooling mortar mixes and concrete. LN was used in doses of 0, 25, 50, 75 and 100% by water volume to either cool the mixing water at T = 4°C or to inject it into concrete mixtures directly. The concrete mix proportions were based on ACI PRC-207.1-21 for mass concrete. The mortars' initial and final setting times and temperatures indicated that a greater percentage of LN delayed the hardening process and the peak hardening rates, exhibiting slower cement hydration. LN cooling enhances the compressive strength of mortar and concrete cubes when VLN/Vwater≤1. However, concrete compressive strength decreased due to ice formation that turned into voids when VLN/Vwater>1. Cooling concrete with chilled water (T = 4°C) showed a 30% and 34.51% increase in mortar and concrete cubes' compressive strength, respectively, and a maximum of 16.45% and 12.97% when LN was injected into mortars and concrete mixes. Cooling the concrete with chilled water (T = 4°C) showed a slower cooling process, which improved cement hydration results.
19 April 2021 in International Journal of Pavement Engineering
Large amounts of waste white cement bypass dust (WCBPD) are generated in huge heaps near white cement factories in Jordan, posing growing environmental concerns related to potential hazardous impact and additional disposal cost. This research evaluates possible and suitable recycling of WCBPD as a partial replacement of Portland cement in the production of the rapidly expanding roller compacted concrete (RCC). This experimental work aims to test the influence of using different proportions (10, 20, 30, and 40%) of WCBPD on the mechanical performance and durability of RCC subjected to sulphate attack. The investigation included compressive strength, a non-destructive test (ultrasonic pulse velocity), water absorption coefficient, and the sulphate linear expansion test. The experimental results were promising for recycling WCBPD as fractions of Portland cement in RCC mixtures at small amounts. Compared to reference cylinders, the reduction in compression strength was about 10, 28, 32 and 39% for 10, 20, 30 and 40% WCBPD replacement ratios, respectively. All RCC mixtures showed satisfactory sulphate resistance since no significant loss in compressive strength nor a significant increase in expansion ratio occurred due to sulphate exposure. The reductions in compressive strength at 180 days of sulphate exposure were 12.8, 15.6, 15.9, 16.1 and 16.6% for RCC cylinders prepared with WCBPD partial replacements of 0, 10, 20, 30 and 40%, respectively.
18 February 2020 in Asian Journal of Civil Engineering