This study investigated the mechanical performance of hybrid tubes made via roll-wrapping and enhanced with an aluminum mesh and epoxy matrix (AL-DMEM). The specimens included Basalt + Jute (BJAJB), Basalt + Bamboo (BBmABmB), Basalt + Banana (BBaABaB), Basalt + Hemp (BHAHB), and Basalt (BAB). The BBmABmB specimen showed the best mechanical properties with the highest peak crushing force, specific energy absorption, mean crushing force, and total energy absorption. The AL-DMEM integration improved load-bearing capacity and energy absorption, reducing matrix cracking and fiber breakage. Scanning electron microscopy and energy-dispersive X-ray analysis highlighted BBmABmB’s robust reinforcement. Its superior structural integrity and aluminum content make it suitable for applications requiring high structural integrity, such as micromobility vehicles, highlighting the potential of AL-DMEM-reinforced composites in advanced engineering applications.
Three-dimensional (3D) printing has emerged as a versatile and sustainable manufacturing route for developing natural fiber–reinforced polymer composites. In this study, the objective is to enhance the mechanical performance and surface quality of 3D-printed polylactic acid (PLA) composites by incorporating powdered pineapple leaf fiber (PLF). Composite filaments were produced using a single-screw extruder and subsequently used to fabricate test specimens through fused deposition modeling. A response surface methodology based on a central composite design was employed to evaluate the influence of fiber content (SFC), infill density (SID), and printing speed (SPS) on ultimate tensile strength (UTS) and surface roughness (Ra). The developed models demonstrated strong statistical reliability, with R 2 values of 0.9823 for UTS and 0.9689 for Ra, as supported by ANOVA. Multi-response optimization yielded an overall desirability of 0.973, corresponding to 34.80 wt% SFC, 77.42% SID, and 62.89 mm/s SPS, resulting in a maximum tensile strength of 73.89 MPa and a minimum surface roughness of 3.36 µm. The optimized composite was further examined to establish the processing–structure–property relationship. Hydrogen-bonding interactions between the hydroxyl groups of poly (lactide) fibers and the carbonyl groups of poly (lactide) were detected using FTIR spectroscopy. X-ray diffraction studies showed a moderate increase in the degree of crystallinity of the composite as a result of fiber-induced nucleation. Thermal gravimetric analysis (TGA) indicated an increase in the thermal stability of the composites. Differential scanning calorimetry (DSC) showed that the thermal transitions were more uniform. The results provide evidence that optimized processing results in good bonding between the polymer and the fiber; the composites are, therefore, characterized by structural uniformity, superior thermomechanical properties, and a data-driven approach to the creation of sustainable, high-performance PLA-based biocomposite materials for use in additive manufacturing processes.
This study investigates the development of biodegradable bio-composites made from polylactic acid (PLA) reinforced with farm waste materials, specifically coconut shell powder and jackfruit skin powder. The bio-composite filaments were fabricated using a filament extruder, and the samples were created through fused deposition modeling (FDM). Mechanical strength, water absorption, and flammability were evaluated. The results revealed that incorporating coconut shell (CBC) and jackfruit skin (JBC) powders into the PLA matrix significantly enhanced the mechanical properties, water resistance, and flame retardancy of the composites. The hybrid bio-composite (HBC) showed a 73.7 % improvement in water absorption resistance, with a water absorption rate of 9.06 ± 0.02 %. CBC and JBC demonstrated 70.8 % and 67.2 % reductions in water absorption, respectively, compared to pure PLA. The HBC bio composite also exhibited superior flame retardancy, with a 60.9 % increase in ignition delay (8.43 ± 0.21 s), 30.5 % reduction in flame spread rate (43.21 ± 1.42 mm min−1), and 50.5 % increase in after-flame duration (13.14 ± 1.05 s). In terms of tensile properties, HBC outperformed all other composites with an ultimate tensile strength (UTS) of 59.2 ± 1.8 MPa, representing a 44.2 % improvement compared to pure PLA. The CBC and JBC showed 24.7 % and 10.7 % increases in UTS, respectively. The HBC also showed a 40.2 % improvement in flexural strength, with the lowest deflection at 4.0 ± 0.1 mm, compared to 23 % and 20.8 % improvements for CBC and JBC, respectively.