ZrSiO4-based pigments have been known to be very stable in ceramic glazes but require a high firing temperature required for phase formation. This study examined the feasibility of using rice husk waste as a substitute for crystalline SiO2. The amorphous form of silica with some impurities was obtained by calcining the rice husk at 800℃. The general chemical formula were (Zr0.9M0.1)SiO4, where M = V, Pr, Fe and Cr. The solid-state processing was achieved by firing at 1300℃ for 12 h with NaF (5 wt%). X-ray Diffraction revealed a lower relative fraction between ZrO2 (secondary phase) and ZrSiO4 in the RHA systems compared to the oxide system for all dopants. Amorphousness of RHA did help enhance phase formability. The particle sizes were in the 3 µm to 5 µm range. Elemental analysis revealed some areas with intense signals of zirconium, indicating unreacted ZrO2 particles. Colorations appeared to be blue, yellow, brown and green for dopants of V, Pr, Fe and Cr, respectively. Technological performance was tested in a practical ceramic glaze and frequently used raw materials fired at its maturation point. The results of this study hold huge potential for using rice husks for sustainable manufacturing of pigments as green products.
Ceramic pigments have been widely used in a variety of industries because of their excellent properties, such as high thermal stability, low-cost productions, and simple manufacturing processes. Re-use of mirror waste, which consists of silicon dioxide greater than 70%, is a method that can reduce raw materials cost. In this work, ceramic pigment with forsterite structure, Mg2SiO4, was synthesized via conventional solid state reaction by using mirror waste as a precursor. Solid solutions of Co-doped forsterite pigment, CoxMg(2−x)SiO4 where x = 0.02–1.6, were calcined at 1000 °C for 2 h. The calcined powders were characterized by X-ray diffraction technique (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), UV-Vis spectrophotometer, and color measurement (CIEL*a*b*). XRD results confirmed that forsterite phase was found as a main phase in the ceramic powder. However, the forsterite phase decreased with increased concentration of Co to x = 0.8–1.6. This could be because of the solubility limit of Co in solid solution. In addition, the use of mirror waste as a raw material was able to reduce calcination temperature compared to the use of oxide reagents. Color measurements or CIEL*a*b* color space of forsterite pigments were located in red-blue quadrant for Co-doped pigment.
25 June 2018 in IEEE Transactions on Nanotechnology
The Cu-doped ZnO (Cu:ZnO) films were prepared by spin-coating with emphasis on a small concentration range (0-5 at-%). Various characterization techniques were employed to examine the correlation between microstructure and properties. X-ray diffraction showed reductions in both cell dimensions and crystallite sizes; the latter was also confirmed by Field-effect scanning electron microscopy. The oxidation state of Cu was studied by X-ray photoelectron spectroscopy to be predominantly 2+. Successful doping was further shed to light by Raman spectroscopy, resulting in a decrease in the band gap which facilitated enhancement in dye degradation. As a result, this Cu:ZnO system holds great potential for possible utilization in the treatment of waste water, especially under normal light radiation.
SrTiO3 is one of the most technologically important dielectric ceramics. In this paper, SrTiO3 nanoparticles were synthesized by a simple sol-gel route using NaOH to adjust the pH of the system. Three different strontium-containing starting precursors (Sr(NO3, SrCl2.6H2O and Sr(CH3COO)2.0.5H2O) were employed. Thermogravimetric analysis (TGA) showed complete decomposition of organics at approximately 800°C; this temperature was chosen as a calcination temperature. At 800°C, 6 hours, only the nitrate route with pH = 10 gives single-phase SrTiO3. Other conditions yield various impurities, most likely due to the incompletion of the reaction although they still contain very broad XRD peaks corresponding to SrTiO3, signifying the probable phase formation capability at these conditions. The obtained SrTiO3 powders are in the nanoscale range of 10 to 40 nm with isotropic morphology.
This study aimed to investigate crystallization of willemite (Zn2SiO4) phase in ceramic glazes. The crystallization behavior of willemite was also characterized by Differential Scanning Calorimetry (DSC). X-ray Diffraction (XRD) revealed three different phases (willemite, anorthite and quartz). Large crystals were examined by Scanning Electron Microscopy (SEM) and were found to be composed of much smaller lath-like crystals. The kinetics of crystal growth was examined via the grain growth kinetics. The growth exponent (n) was approximately 2 which could be explained by the mechanism of grain boundary mobility. The activation energy (G) values were found to vary with temperature, signifying complication in thermodynamic phenomena during the growth process.
24 October 2011 in Applied Mechanics and Materials
In this work, systematic substitution of ZnO with SnO2 in ZnO-based varistor composition was investigated through analysis of densification, phase formation, microstructure and non-linear properties. The general formula was Zn0.96-xSnxBi0.02Co0.02Oβ with x = 0, 0.01, 0.02 and 0.04. The high rate of densification starting at 800°C is believed to be related to Bi2O3 via liquid-phase sintering. The complex nature of this multi-phasic varistor system was demonstrated through occurrence of different phases at different sintering temperatures. The low-temperature pyrochlore (Bi2Sn2O7) started to dissociate at approximately 1100°C with the spinel (Zn2SnO4) forming afterwards. The grain size variation with composition might be induced by the changes in the availability of Bi2O3 which has been reported to help facilitate abnormal grain growth. All samples sintered at 1200°C, with data extrapolation, possessed breakdown voltages of higher than 1400 V/cm.