Barium titanate (BaTiO3) has been recognized as an important perovskite ceramic since its discovery due to its excellent dielectric, ferroelectric and piezoelectric properties. Its modifications have been studied in many perspectives depending on applications. In this review, the basic principles of BaTiO3 were described, then followed by the explanation on the recent modifications of BaTiO3 to improve the dielectric properties. Relaxor ferroelectric behavior of BaTiO3 was revealed by combining BaTiO3 with other Bi-based perovskites. These modified- BaTiO3 opened the opportunities for emerging energy storage applications. Next, the modifications for ferroelectric and ferromagnetic aspects were further discussed. BaTiO3 can also be doped by other ions to enhance such properties. Solid solution between Bi-based perovskites such as BiFeO3, (Bi0.5K0.5)TiO3, or Bi(Zn0.5Ti0.5)O3 and BaTiO3 can also improve ferroelectric and ferromagnetic properties. Therefore, these details of recent BaTiO3 modifications may provide guidance for the next BaTiO3 investigations in order to gain the maximum benefits from BaTiO3.
Silver–tantalum (Ag–Ta) thin films were fabricated by magnetron co-sputtering on silicon (Si) wafer (100) and glass slide substrates at room temperature. The Ag–Ta thin films were prepared at various deposition times of 5, 10, 20 and 30 s and the physical, structural and optical properties of the Ag–Ta thin films were investigated. It was determined that the thicknesses of the films were 7, 9, 17 and 33 nm, respectively. The results revealed that an increase in the film thickness leads to a monotonic increase in FCC and BCC phase of Ag and Ta, respectively. The work function and stoichiometric of the Ag–Ta thin films were investigated by ultraviolet and X-ray photoemission spectroscopies (UPS and XPS), respectively. The potential of Ag–Ta thin films to be used as low-emission coating was investigated using a spectrophotometer. A UV–VIS–NIR spectrophotometer was used to measure the spectral reflectance in the wavelength range from 300 to 2000 nm. The results showed that the Ag–Ta thin film deposited for 30 s exhibited higher reflectance in NIR region than those of 5, 10, 20 and 30 s. It demonstrated an average reflectance of about 80% and slightly decreased to 75% after being kept in the air atmosphere for 28 days. It can be likewise proposed as an alternative thin film with high reflectance of NIR radiation single layer to develop industrial low-emission coating for cost-effective, clean, and easy adaptation to a large area coating.
Ceramic pigments have been widely used in a variety of industries because of their excellent properties, such as high thermal stability, low-cost productions, and simple manufacturing processes. Re-use of mirror waste, which consists of silicon dioxide greater than 70%, is a method that can reduce raw materials cost. In this work, ceramic pigment with forsterite structure, Mg2SiO4, was synthesized via conventional solid state reaction by using mirror waste as a precursor. Solid solutions of Co-doped forsterite pigment, CoxMg(2−x)SiO4 where x = 0.02–1.6, were calcined at 1000 °C for 2 h. The calcined powders were characterized by X-ray diffraction technique (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), UV-Vis spectrophotometer, and color measurement (CIEL*a*b*). XRD results confirmed that forsterite phase was found as a main phase in the ceramic powder. However, the forsterite phase decreased with increased concentration of Co to x = 0.8–1.6. This could be because of the solubility limit of Co in solid solution. In addition, the use of mirror waste as a raw material was able to reduce calcination temperature compared to the use of oxide reagents. Color measurements or CIEL*a*b* color space of forsterite pigments were located in red-blue quadrant for Co-doped pigment.
Phase formations and dielectric properties of lead free barium titanate bismuth zinc zirconate, BaTiO3-Bi(Zn0.5Zr0.5)O3 (BT-BZZ), were comparatively investigated between two different synthesis routes, solid state reaction and salt flux assistance methods. The perovskite (1-x)BT-(x)BZZ ceramics, where x = 0.02, 0.05 and 0.10, were synthesized by using reagent grade oxides and the NaCl salt was used as a surface active agent to lower the calcination temperature. Phase formations were examined by X-ray diffraction technique (XRD). It was found that the solid solutions of (1-x)BT-(x)BZZ can be obtained with lower temperature at least 200 °C via salt flux assistance method. The NaCl salt addition could result in single phase of perovskite structure at every compositions with the calcination temperature as low as 800 °C. Dielectric measurements revealed that the Curie temperature (Tc) shifted to lower temperature with increase of BZZ concentration. Moreover, the dielectric behavior transformed to diffuse phase transition when x = 0.1. The samples prepared via salt flux assistance method exhibited smaller grain size which were revealed by scanning electron microscope. In addition, P-E hysteresis measurements illustrated the higher high E-field dielectric constant with the narrower P-E loop when the salt flux was applied.
T he aim of this work was to study the preparation of luminescent glass samples using microwave technique. Borosilicate glass powder and dysprosium oxide (Dy2O3) as the luminescent phosphor were mixed with the concentration ranging between 0.0-0.5 mol%. The glass pellets were successfully prepared via microwave heating with a power of 800 watts for 24 minutes. The samples exhibited dispersion of pores within the glass matrix which could be the origin of white translucent characteristics. The XRD results showed an amorphous structure which revealed the completely dissolution of Dy2O3 within the samples. The luminescence properties of the samples were tested via photoluminescence spectrometer, revealing that the glass doped with dysprosium emitted white light with the maximum emission occurring at a wavelength of 576 nm. The CIE chromacity characteristics confirmed the white emission of the glass samples. In addition, it was found that the decay time of the luminescent glass decreased with an increase in the concentration of the luminescent phosphor. This may be caused by the energy transfer of electrons through cross relaxation.