In this study, modeling of optimized lattice mismatch by carbon-dioxide annealing on (In, Ga) co-doped ZnO multi-deposition thin films was investigated with crystallography and optical analysis. (In, Ga) co-doped ZnO multi-deposition thin films with various types of bottom layers were fabricated on sapphire substrates by solution synthesis, the spin coating process, and carbon-dioxide laser irradiation with post annealing. (In, Ga) co-doped ZnO multi-deposition thin films with Ga-doped ZnO as the bottom layer showed the lowest mismatch ratio between the substrate and the bottom layer of the film. The carbon-dioxide laser annealing process can improve electrical properties by reducing lattice mismatch. After applying the carbon-dioxide laser annealing process to the (In, Ga) co-doped ZnO multi-deposition thin films with Ga-doped ZnO as the bottom layer, an optimized sheet resistance of 34.5 kΩ/sq and a high transparency rate of nearly 90% in the visible light wavelength region were obtained.
In this study, the characteristics in the lead-free piezoelectric ceramic 0.5Ba(Zr0.2Ti0.8)O3−0.5(Ba0.7Ca0.3)TiO3 (0.5BZT–0.5BCT) were investigated to assess its potential for Rosen-type piezoelectric transformers. This piezoelectric ceramic has a piezoelectric charge coefficient d33 of 430 pC/N, an electromechanical coupling factor kp of 49%, a dielectric constant εr of 2836, a remnant polarization Pr of 4.98 μC/cm2, and a coercive electric field Ec of 2.41 kV/cm. Sb2O3 was soft doped with 0.05, 0.1, 0.15, and 0.2 mol%, respectively, and exhibited excellent physical properties at 0.1 mol%. Based on this, a piezoelectric transformer was fabricated and measured, and it showed better output characteristics than pure 0.5BZT–0.5BCT. The amplification ratio (Vout/Vin) was optimized based on the device geometry and properties of the piezoelectric material. Moreover, the output characteristics of the Rosen−type piezoelectric transformer were simulated with the PSpice program. Output values of the fabricated and simulated piezoelectric transformers for the r vibrational frequency were compared and analyzed. Accordingly, the step-up amplification ratios Vout/Vin of the fabricated and simulated devices at the vibrational frequency were compared as well. This piezoelectric transformer could replace silicon steel transformers and be used for the creation of black light and for laptop chargers.
In this study, the composition of lead-free piezoelectric ceramics (1 − x)(Bi0.5Na0.5)TiO3–x(Ba0.5Sr0.5)TiO3 with excellent piezoelectric properties was investigated. Crystal analysis and electrical and piezoelectric properties were analyzed according to the content of the BST composition. A phase change from rhombohedral to tetragonal structure was observed in 0.12 BST, and the densest and most uniform microstructure was confirmed in this composition. The dielectric constant increased from 905 to 1692 as the composition of BST increased to 0.12 BST. Afterward, as the composition of BST increased, the permittivity tended to decrease. Additionally, at 0.12 BST, Pr was the highest at 23.34 μC/cm2. The piezoelectric charge constant (d33) and the electromechanical coupling coefficient (kp) were 152 pC/N and 0.37, respectively, and showed the highest values at 0.12 BST. Curie temperature (Tm) was analyzed 242 °C at 0.12 BST, the optimal composition. It was confirmed that the characteristics of 0.12 BST were excellent in all conditions. Therefore, it was confirmed that 0.12 BST is the optimal composition for (1 − x)BNT–xBST piezoelectric ceramics.