Kok Hwa Yu

Dr. Kok Hwa Yu


Research Focus & Metrics

Academic Career Length

35Years (1992-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2010 in Engineering Analysis with Boundary Elements
Verified
Journal Article
Closed access
KYKok Hwa Yu
Kok Hwa Yu
AKA. Halim Kadarman
A. Halim Kadarman
HDHarijono Djojodihardjo
Harijono Djojodihardjo

22 May 2019 in Energies
Verified
Journal Article
Open access
PDF file
Yew Heng TeohYew Heng Teoh
Yew Heng Teoh
KYKok Hwa Yu
Kok Hwa Yu
HHH.G. How
H.G. How
HNHuu Tho Nguyen
Huu Tho Nguyen
In the present study, the effects of adding of bioethanol as a fuel additive to a coconut biodiesel-diesel fuel blend on engine performance, exhaust emissions, and combustion characteristics were studied in a medium-duty, high-pressure common-rail turbocharged four-cylinder diesel engine under different torque conditions. The test fuels used were fossil diesel fuels, B20 (20% biodiesel blend), B20E5 (20% biodiesel + 5% bioethanol blend), and B20E10 (20% biodiesel + 10% bioethanol blend). The experimental results demonstrated that there was an improvement in the brake specific energy consumption (BSEC) and brake thermal efficiency (BTE) of the blends at the expense of brake specific fuel consumption (BSFC) for each bioethanol blend. An increment in nitrogen oxide (NOx) across the entire load range, except at low load conditions, was found with a higher percentage of the bioethanol blend. Also, it was found that simultaneous smoke and carbon monoxide (CO) emission reduction from the baseline levels of petroleum diesel fuel is attainable by utilizing all types of fuel blends. In terms of combustion characteristics, the utilization of bioethanol blended fuels presented a rise in the peak in-cylinder pressure and peak heat release rate (HRR) at a low engine load, especially for the B20E10 blend. Furthermore, the B20E10 showed shorter combustion duration, which reduced by an average of 1.375 °CA compared to the corresponding baseline diesel. This study therefore showed that the B20E10 blend exhibited great improvements in the diesel engine, thus demonstrating that bioethanol is a feasible fuel additive for coconut biodiesel-diesel blends.

1 February 2016 in Physics of Fluids
Verified
Journal Article
Closed access
KYKok Hwa Yu
Kok Hwa Yu
CTC. J. Teo
C. J. Teo
BKB. C. Khoo
B. C. Khoo
The modal analysis of pressure-driven flows in channels patterned with superhydrophobic surfaces containing periodic grooves and ribs aligned longitudinally to the flow direction has been performed. The effects of shear–free fraction δ and groove-rib spatial period normalized by full-channel height L on the linear flow stability of such flows have been explored. By performing a BiGlobal linear stability analysis via the pseudo-spectral method, such surfaces have been found to potentially exert a stabilizing or destabilizing effect on the base flow, depending predominantly on the normalized groove-rib spacing. For small values of L (i.e., L = 0.01 and 0.02), a stabilizing effect is predicted for flows over longitudinal superhydrophobic grooves, in agreement with the results obtained using a local stability analysis which employs a homogeneous slip condition along the walls. For a moderate value of normalized groove-rib spacing where the groove-rib periodic spacing is one-tenth of the channel height, the presence of longitudinal superhydrophobic grooves leads to flow instabilities at a lower critical Reynolds number. The redistribution of the base flow resulting from the vanishing shear rates along the liquid-gas interface could give rise to an inflectional instability that promotes temporal instability. The effects of patterning the superhydrophobic surfaces on one or both channel walls are also examined.

27 July 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
M AbdullahM Abdullah
M Abdullah
KYKok Hwa Yu
Kok Hwa Yu
HLHao Yuan Loh
Hao Yuan Loh
RKRoslan Kamarudin
Roslan Kamarudin
Prem GunnasegaranPrem Gunnasegaran
Prem Gunnasegaran
AAAbdusalam Imhmed Alkhwaji
Abdusalam Imhmed Alkhwaji
Nanofluids are frequently employed in numerous heat transfer applications due to their improved thermophysical properties compared to a base fluid. By selecting suitable combinations of nanoparticles, hybrid nanofluids can have better thermophysical properties than mono nanofluids. Thus, this study examines the effect of volume fractions of hybrid nanofluids on different thermophysical properties, such as density, thermal conductivity, specific heat, and dynamic viscosity. Thermophysical properties of copper–nickel (Cu–Ni) water-based hybrid nanofluids are determined using molecular dynamic (MD) simulation for different volume fractions of 0.1–0.3%. Results show that the density, thermal conductivity, and viscosity of Cu–Ni hybrid nanofluids increase with volume fraction, whereas the specific heat capacity at a constant pressure decreases with volume fraction. These properties are validated for the base fluid, mono nanofluids, and hybrid nanofluids. Results are in good agreement with previous findings. The thermophysical properties of Cu–Ni hybrid nanofluids significantly improve and have better characteristics for cooling fluids than the base fluid.

1 December 2018 in Fuel
Verified
Journal Article
Closed access
YTY.H. Teoh
Y.H. Teoh
HMH.H. Masjuki
H.H. Masjuki
HHH.G. How
H.G. How
MKM.A. Kalam
M.A. Kalam
KYKok Hwa Yu
Kok Hwa Yu
AAA. Alabdulkarem
A. Alabdulkarem

6 September 2021 in Circuit World
Verified
Journal Article
Closed access
CSChun Hei Edmund Sek
Chun Hei Edmund Sek
M AbdullahM Abdullah
M Abdullah
KYKok Hwa Yu
Kok Hwa Yu
SWShaw Fong Wong
Shaw Fong Wong
Purpose: This study aims to simulate molded printed circuit board (PCB) warpage behavior under reflow temperature distribution. Simulation models are used to estimate dynamic warpage behavior for different form factor sizes. Design/methodology/approach: This study analyzes warpage during the reflow process. The shadow moiré experiment methodology is used to collect data on the dynamic warpage performance of a model with a form factor of 10mm × 10mm × 1mm. The temperature profile with heating from 25°C to 300°C at intervals of 50°C is used, and the sample is made to undergo a cooling process until it reaches the room temperature. Subsequently, ANSYS static structural simulation is performed on similar form factor models to ascertain the accuracy of the simulation results. Findings: Results show that the deformation and total force induced by coefficient of thermal expansion (CTE) mismatch are examined based on the warpage performance of models with different sizes, that is, 45mm × 45mm × 1mm and 45mm × 15mm × 1mm. Compared with the experimental data, the simulated modeling accuracy yields a less than 5% deviation in the dynamic warpage prediction at a reflow temperature of 300°C. Results also reveal that the larger the model, the larger the warpage changes under the reflow temperature. Research limitations/implications: The simulated warpage is limited to the temperature and force induced by CTE mismatch between two materials. The form factor of the ball-grid array model is limited to only three different sizes. The model is assumed to be steady, isothermal and static. The simulation adopts homogenous materials, as it cannot accurately model nonhomogeneous multilayered composite materials. Practical implications: This study can provide engineers and researchers with a profound understanding of molded PCB warpage, minimal resource utilization and the improved product development process. Social implications: The accurate prediction of molded PCB warpage can enable efficient product development and reduce resources and production time, thereby creating a sustainable environment. Originality/value: The literature review points out that warpage in various types of PCBs was successfully examined, and that considerable efforts were exerted to investigate warpage reduction in PCB modules. However, PCB warpage studies are limited to bare PCBs. To the best of the authors’ knowledge, the examination of warpage in a molded PCB designed with a molded compound cover, as depicted in Figure 3, is yet to be conducted. A molded compound provides strong lattice support for PCBs to prevent deformation during the reflow process, which is a topic of considerable interest and should be explored.