The effect of nitrogen addition on the microstructure formation and hardness during solidification and heat treatment was investigated and the possibility of nitrogen as an alloying element was discussed in terms of alloy chemistry for high-carbon high-speed tool steel type cast alloys. Nitrogen with a concentration from 48 ppm to 1542 ppm was successfully introduced by mixing Cr2N into a molten alloy. Analysis of the diffraction pattern revealed that the primary V2CN carbonitride crystallized upon the addition of nitrogen, whereas eutectic carbides mainly formed in N-free specimens. The chemical composition of the carbonitride is also affected by the addition of nitrogen. With increasing quenching temperature, the Vickers hardness gradually increased to a peak and then decreased. Nitrogen addition helps to increase the hardness similarly to carbon. A N-containing specimen also exhibited superior secondary hardening after tempering. It is known that a large amount of residual austenite finally transforms to a hard martensite phase after tempering. According to the results of XRD analysis, nitrogen addition increases the volume fraction of retained austenite in the matrix at a higher holding temperature. Furthermore, the precipitation of nanosize carbonitride was observed around the primary V2CN carbonitride in addition to the standard precipitation. Therefore, this carbonitride precipitation may induce the superior secondary hardening and ultimately increase the macrohardness of N-containing specimens. This Paper was Originally Published in Japanese in J. Japan Inst. Met. Mater. 79 (2015) 169–175.
In the industrial steel manufacturing process, such as continuous casting and ingot casting, macrosegregation occurs due to the effect of bridging and contraction flow during the middle and end periods of solidification. Since the macrosegregation results in a nonuniform structure and eventually cracks, there has been a demand for technological development that does not cause macrosegregation in the casting process. In this study, model experiments using the medium-carbon steel cast with a laboratory-scale local-chilled mold at different superheating have been carried out to investigate the relationship between solidified structure and macrosegregation occurred by local bridging during casting. The morphology of shrinkage porosities and dendrite structures was observed. The concentrations of the alloying elements were analyzed for macrosegregation by an electron probe micro-analyzer. Chill plates successfully formed the columnar dendrite bridging area and the columnar dendrite shell in the sample with high superheating. During solidification, the negative pressure of the region below the bridging increased, and the concentrated contraction flow flowed into the bottom of the large shrinkage porosity. Finally, V segregation was formed in the bridging area, large shrinkage porosities remained below the bridging area, and point-like or band-like positive macrosegregation occurred in the interdendritic region between columnar dendrites and equiaxed dendrites below the bridging. In comparison, a lower casting temperature increased the grain density and formed shrinkage porosities that were smaller in size but larger in number and more dispersed.
We have observed circular polarization of Sgr A* at 100 GHz using the Nobeyama 45‐m telescope. The circular polarization of Sgr A* in its quiescent phase was |mc| ≤ 0.5% after subtraction of the contribution from free‐free emission surrounding Sgr A*.
Currently, steel products are manufactured by continuous casting or large-sized ingot casting, and macrosegregation that occurs during the manufacturing process significantly impacts product quality in terms of cracks and deterioration of mechanical properties. To clarify the principle of casting defects, such as shrinkage porosity and macrosegregation due to the formation of bridging of the columnar dendrite of the medium-carbon steel, in this experiment, a laboratory-scale local-chilled mold in which the middle part was forcedly cooled was designed to cause bridging, shrinkage porosities, and macrosegregation. Enough risers were also designed to simulate realistic gravity casting as much as possible. The solidification structure morphology was observed, concentration analysis of alloying elements was performed, and the effect of bridging on macrosegregation was investigated. Solidification proceeded preferentially from the chill plate, and the bridging was formed successfully at a high casting temperature. The high casting temperature condition could cause bridging, but large shrinkage porosities would be formed as well. On the contrary, the lower casting temperature condition could increase the grain density and form shrinkage porosities that are smaller in size but larger in number and more dispersed, compared with the case cast with no chill plate mold. Due to the formation of bridging, macrosegregation was formed, and the difference between positive and negative segregation was increased from the longitudinal center of the sample.
Fire investigators have attempted to study fire behaviors through microstructural examination of molten marks on copper wire. However, there have not been many studies on the metallurgical examination of real-world cases. This research examined the surface morphology and microstructure in the longitudinal section of molten marks on copper wire from various fire scenes to explain how they formed and identify the surrounding materials. The results show that the foreign elements discovered via EDS on the surface of molten marks vary depending on their environment. Molten mark microstructures differed even if they were collected from the same fire scene; a distinct microstructure implies different molten mark formations. Moreover, the presence of residual elements in the microstructure indicates the existence of surrounding materials during formation in a fire. Therefore, microstructural diversity and the presence of residual elements may guide fire investigators in explaining the formation of molten marks and the fire environment for fire investigation.
A technique, which can explain the behavior of fires by using microstructural and oxide examinations of melted marks on copper wire, has been required for fire investigators. However, a study on the microstructural and oxide evolution after a fire is insufficient due to various and complicated fire conditions. In this research, changes in surface morphology, oxide layer thickness, oxidation kinetics, and microstructure were investigated at various annealing temperatures and times on the melted mark on the copper wire. The results show that the copper dendrites surrounded by (Cu+Cu2O) eutectic structure under Cu2O and CuO surface is the fingerprint of melted mark on copper wire annealed between 220°C and 600°C. At an annealing temperature of 800°C to 1000°C, the characteristic microstructure of the melted mark is Cu2O precipitates without dendrites in grains under a single layer of Cu2O. Moreover, the diffusion processes contributed to Cu2O growth could be as follows: lattice diffusion at 220°C to 400°C and grain boundary diffusion at 400°C to 1000°C.