Reinforced polymer composites are a recent type of advanced shielding material that has been studied experimentally and theoretically. This work described the protection properties of silicon rubber filled with nano and micro tin oxide (II). These shielding materials are evaluated by parameters such as mass attenuation coefficient, linear attenuation coefficient, mean free path, effective atomic number, and buildup factor. The morphology and mechanical properties of silicon rubber, which is reinforced with tin oxide (II) particles in terms of weight fraction and size, have been studied. The results explain that the mass attenuation coefficient increases as tin oxide (II) concentration increases at a particular photon energy. It was found that the shielding properties of nano tin oxide (II) composites are more effective than micro tin oxide (II) composites against gamma rays. The effective atomic number values increase by increasing tin oxide (II) and so on equivalent atomic number. On the other hand, increasing tin oxide (II) weight fraction led to an increase in buildup factor maximum, which proved that tin oxide (II) concentration has significant effectiveness in radiation protection.

In this study, we investigated a novel polymer nano-composite, PS-PbO, containing two distinct nano-sizes of lead oxide nanoparticles (PbO-A and PbO-B), in addition to the bulk size (PbO-K). These nanoparticles were embedded separately in a polystyrene (PS) matrix at different weight percentages (10%, 15%, 25%, and 35%) using roll mill mixing and compressing molding. Our evaluation focused on the radiation attenuation ability of PS-PbO and the effect of particle size, considering gamma-ray energies ranging from 0.06 to 1.3 MeV (from sources like ²⁴¹Am, ¹³³Ba, ¹³⁷Cs, and ⁶⁰Co). The linear attenuation coefficient (LAC) was determined by analyzing samples of the synthesized composite with different thicknesses. Then, various shielding parameters were calculated, including total molecular, atomic, and electronic cross-sections (σ_mol, σ_atm, σ_el), as well as the effective atomic number and the electron density (Z_eff and N_eff). Surprisingly, modifying PbO particle sizes had a significant impact on shielding efficiency. For instance, the composite with 25 wt% of the smallest PbO-B particles showed a 26.7% increase in LAC at 0.059 keV compared to the composite with 25 wt% of PbO-K (larger particles). Notably, the LAC peaked at low energy (0.059 keV), close to the K-edge of Pb, where interaction is directly proportional to Z⁴. With increasing PbO concentrations, the LAC of PS-PbO composites increased steadily. Additionally, as PbO concentration increased, the composite’s effective atomic number Z_eff and the electron density N_eff increased, leading to a greater total Gamma-ray interaction cross-section. Furthermore, when comparing the Half-Value Layers of the novel nanocomposite to traditional lead shielding, a 70% reduction in mass was observed. Notably, the composite containing the smallest nano-size of PbO exhibited the highest radiation-shielding efficiency among all combinations and could therefore be used to create inexpensive and lightweight shields.

Recently, there has been a surge of interest in the application of radiation-shielding materials. One promising research avenue involves using free-lead metal oxides/polymer composites, which have been studied for their radiation shielding and characterization properties. This study reinforced the dimethylpolysiloxane (silicone rubber) composites with micro- and nano-sized particles of tin oxide, cadmium oxide, and bismuth oxide as additive materials. The composites were tested with 20 and 50 weight fractions, and their attenuation coefficients were measured using a NaI(TI) detector at gamma-ray energies ranging from 59.54 to 1408.01 keV. Also, the thermal and mechanical properties of the composites were observed and compared with those of free silicone rubber. The results showed that the 50% nano metal oxide/SR composites exhibited better thermal stability and attenuation properties than the other composites, also possessing unique attributes such as lightweight composition and exceptional flexibility. Consequently, this composite material holds immense potential for safeguarding vital organs, including the eyes and gonads, during radiological diagnosis or treatment procedures. Its exceptional ability to absorb a significant portion of incident rays makes it an invaluable asset in the field of radiation protection.

In the current study, the gamma-radiation-shielding characteristics of novel gypsum–lime–waste marble-based mortars reinforced with micro-PbO and nano-PbO powders were investigated. In total, seven mortar groups, including a control mortar (named GLM), were prepared. The other groups contained10, 20, and 30 wt.% of both micro-PbO and nano-PbO as a waste marble replacement. This study aimed to explore the effect of particle size and concentrations of PbO powders on the γ-ray-shielding capability of GLM mortars. For this purpose, an HPGe detector and five standard radioactive point sources (²⁴¹Am, ¹³³Ba, ¹³⁷Cs, ⁶⁰Co, and ¹⁵²Eu) were employed to measure different shielding parameters, including the linear attenuation coefficient (μ), mass attenuation coefficient (μ_m), mean free path (MFP), half-value layer (HVL), and tenth-value layer (TVL), for the prepared samples in the energy range between 59.53 keV to 1408.01 keV. On the basis of μ_m values, other significant shielding parameters such as effective atomic number (Z_eff), effective electron density (N_eff), equivalent atomic number (Z_eq), and exposure buildup factor (EBF) were also computed to explore the potential usage of the proposed mortars as radiation protective materials. The results reported that the smallest HVL, TVL, and MPF, as well as the largest attenuation values, were obtained for mortars reinforced by nano-PbO compared to those containing micro-PbO. It can be concluded from the results that the mortar samples containing nano-PbO had a remarkably improved gamma-radiation-shielding ability. Thus, these mortars can be used for radiation shielding on walls in nuclear facilities to reduce the transmitted radiation dose.

This study aims to explore the radiation protection properties of white mortars based on white cement as a binder and Bi₂O₃ micro and nanoparticles in proportions of 15 and 30% by weight as replacement sand. The average particle size of micro- and nano-Bi₂O₃ was measured using a transmission electron microscope (TEM). The cross-sectional morphology and distribution of Bi₂O3 within the samples can be obtained by scanning electron microscopy (SEM), showing that nanoscale Bi₂O₃ particles have a more homogeneous distribution within the samples than microscale Bi₂O₃ particles. The shielding parameters of the proposed mortars were measured using the HPGe detector at various γ-ray energies emitted by standard radioactive point sources ²⁴¹Am, ¹³³Ba, ⁶⁰Co, ¹³⁷Cs, and ¹⁵²Eu. The experimental values of the prepared mortars’ mass attenuation coefficients (MAC) match well with those determined theoretically from the XCOM database. Other shielding parameters, including half value layer (HVL), tenth value layer (TVL), mean free path (MFP), effective electron density (N_eff), effective atomic number (Z_eff), equivalent atomic number (Z_eq), and exposure buildup factor (EBF), were also determined at different photon energies to provide more shielding information about the penetration of gamma radiation into the selected mortars. The obtained results indicated that the sample containing 30% by weight of nano Bi₂O₃ has the largest attenuation coefficient value. Furthermore, the results show that the sample with a high concentration of Bi₂O₃ has the highest equivalent atomic numbers and the lowest HVL, TVL, MFP, and EBF values. Finally, it can be concluded that Bi₂O₃ nanoparticles have higher efficiency and protection compared to microparticles, especially at lower gamma-ray energies.

Due to the present industrial world, the risk of radioactivity is notably increasing. Thus, an appropriate shielding material needs to be designed to protect humans and the environment against radiation. In view of this, the present study aims to design new composites of the main matrix of bentonite–gypsum with a low-cost, abundant, and natural matrix. This main matrix was intercalated in various amounts with micro- and nanosized particles of bismuth oxide (Bi₂O₃) as the filler. Energy dispersive X-ray analysis (EDX) recognized the chemical composition of the prepared specimen. The morphology of the bentonite–gypsum specimen was tested using scanning electron microscopy (SEM). The SEM images showed the uniformity and porosity of a cross-section of samples. The NaI (Tl) scintillation detector was used with four radioactive sources (²⁴¹Am, ¹³⁷Cs, ¹³³Ba, and ⁶⁰Co) of various photon energies. Genie 2000 software was used to determine the area under the peak of the energy spectrum observed in the presence and absence of each specimen. Then, the linear and mass attenuation coefficients were obtained. After comparing the experimental results of the mass attenuation coefficient with the theoretical values from XCOM software, it was found that the experimental results were valid. The radiation shielding parameters were computed, including the mass attenuation coefficients (MAC), half-value layer (HVL), tenth-value layer (TVL), and mean free path (MFP), which are dependent on the linear attenuation coefficient. In addition, the effective atomic number and buildup factors were calculated. The results of all of these parameters provided the same conclusion, which confirms the improvement of the properties of γ-ray shielding materials using a mixture of bentonite and gypsum as the main matrix, which is much better than using bentonite alone. Moreover, bentonite mixed with gypsum is a more economical means of production. Therefore, the investigated bentonite–gypsum materials have potential uses in applications such as gamma-ray shielding materials.