Ruthenium (Ru) exhibits excellent electrical properties at the nanoscale, and it can be used to replace Al and Cu as interconnect metals for nodes of 20 nm and below in the next generation of integrated circuits. Ru interconnects mainly exist in the form of films, and Ru targets are used as the key raw materials to produce these films. Establishing whether there is an inheritance relationship in terms of microstructure and electrical properties between these targets and the resultant films will determine whether these are important factors for improving the electrical properties of Ru films and will provide directional guidance for the preparation of Ru targets. In this work, Ru targets were prepared by vacuum hot pressing with two different Ru powders with different morphologies and particle sizes. Ru films were then deposited on SiO2/Si(100) substrates by RF magnetron sputtering at substrate temperatures ranging from room temperature (RT, about 25 °C) to 400 °C. The microstructures and electrical properties of the Ru targets and Ru films were investigated by high-resolution field-emission scanning electron microscopy, x ray diffraction, atomic force microscopy, four-probe resistivity measurements, and digital conductivity tests. The results showed that Ru targets with a more uniform microstructure had lower resistivity; furthermore, Ru films deposited by Ru targets with a more uniform microstructure were preferentially crystallized, and they also had a faster average deposition rate, a smaller average grain size, and lower surface roughness. However, no correlation was found between the crystal orientations of the Ru films and Ru targets.
Nickel (Ni) thin films are commonly used in the integrated circuit field. Magnetron sputtering is a common method for thin film deposition, and the sputtering target is the key raw material in the magnetron sputtering process. In this work, cold-rolled and annealed Ni targets were prepared. The microstructures and magnetic properties of the Ni targets were analyzed. Then, Ni films were prepared by direct current magnetron sputtering with the above two Ni targets. The Ni films were characterized by scanning electron microscopy, atomic force microscopy, grazing incidence x-ray diffraction, x-ray reflectivity, and four-probe testing. Finally, the surface morphologies of the targets were compared before and after sputtering, and the relationships between the Ni targets and the Ni films were discussed. The results show that with the same conditions, the annealed Ni target is more efficiently utilized, and the electrical properties of the Ni films are good when the film is macrostructurally smooth and microstructurally compact. This is due to the target texture, magnetic properties, etc.
The inherent temperature-dependent sublattice preference of constituent atoms in FCC_CoCuNi multi-principal element alloys (MPEAs) is theoretically predicted by combining a two-sublattice model based on the L12_AuCu3 prototype with computational thermodynamics, which extends beyond the commonly-believed, yet unreasonable randomly mixing solid solution hypothesis. Based on the predicted sublattice occupied fractions (SOFs) and available computer resource, two MPEAs atom distributing models with different sizes are established for different applications, respectively, where the bigger size model is further employed to analyze statistically the atom distributing character quantitatively and graphically, while the smaller size model is employed to study the lattice distortion of MPEAs further using first-principles calculations density functional theory. The atom distributing configurations of some representative heat treatment temperatures, as well as the hypothetical randomly mixing structure are compared. It is revealed that FCC_CoCuNi MPEAs exhibit strong temperature-dependent ordering behavior. The SOFs-based configurations are (Ni1.0000)1a(Co0.4445Cu0.4444Ni0.1111)3c, (Co0.0653Cu0.0721Ni0.8626)1a(Co0.4227Cu0.4204Ni0.1569)3c, and (Co0.1574Cu0.1593Ni0.6833)1a(Co0.3920Cu0.3913Ni0.2167)3c at 100 K, 900 K, and 1400 K, respectively. Overall, Ni atoms always prefer to 1a sublattice and the preference tendency reduce a little bit at considerable high temperatures. The configurational entropies of FCC_CoCuNi MPEAs increase with the increase of heat treatment temperature, while they are considerably lower than that of the hypothetical ideal random solid solution. Based on the atom distributing model of MPEAs, the local atomic cluster characteristics are further investigated by statistically analyzing the coordination numbers of the constituent atom coordinated with the same type of atoms. The radial distribution function (RDF) further verified the atom aggregating behavior. For most family of crystal planes in FCC_MPEAs, except {1 1 1}, there are obviously different atom distributing characters between the even and odd layers. The atom distributing model of some representative bulk structure and surface structure are afforded valuably for reference and application both in experimental and theoretical investigation further. Thus, rich and indispensable structural genome data are afforded for the further research and development of the promise FCC_CoCuNi MPEAs intensively.