Doped polysilicon (poly-Si) passivating contacts have emerged as a key technology for the next generation of silicon solar cells in mass production, owing to their excellent performance and high compatibility with the existing passivated emitter and rear cell technology. However, the current solar cell architecture based on a rear-side electron-selective (n+) poly-Si contact is also approaching its practical limit (∼26%) in mass production. The full potential of doped poly-Si passivating contacts can only be realized through incorporation of both electron-selective and hole-selective (p+) poly-Si contacts. While studies of both p+ and n+ poly-Si contacts commenced simultaneously, significant performance differences have arisen. Phosphorus-doped poly-Si contacts consistently outperform boron-doped counterparts, displaying typically lower recombination current density (J0) values (1–5fA/cm2 vs 7–15fA/cm2). This discrepancy can be attributed to inadequate optimization of p+ poly-Si contacts and fundamental limitations related to boron doping. The poorer passivation of p+ poly-Si contacts can be at least partly attributed to boron segregation into the interfacial oxide layers, compromising the interfacial oxide integrity and reducing the chemical passivation effectiveness. This review critically examines the progress of p+ poly-Si contacts characterized by cell efficiency and J0 values, delves into existing challenges, identifies potential solutions, and explores some potential solar cell architectures to enhance efficiency by incorporating p+ poly-Si contacts.
3 July 2025 in Solar Energy Materials and Solar Cells
This paper investigates the potential of three different methods-tabula rasa (TR), phosphorus diffusion gettering (PDG), and hydrogenation, for improving the carrier lifetime in n-type Czochralski-grown upgraded metallurgical-grade (UMG) silicon samples. Our results show that the lifetimes in the UMG wafers used in this study were affected by both mobile metallic impurities and as-grown oxygen precipitate nuclei. Thus, the dissolution of grown-in oxygen precipitate nuclei via TR and the removal of mobile impurities via PDG step were found to significantly improve the electronic quality of the UMG wafers. Finally, we report bulk lifetimes and 1-sun implied open-circuit voltages of the UMG wafers after boron and phosphorus diffusions, as typically applied in n-type cell fabrication.
Herein, a systematic study of the electronic quality of gallium‐doped p‐type silicon wafers from Czochralski‐grown ingots with melt recharging is presented. It is found that in the as‐grown state, the ingots contain interstitial iron concentrations in the range of 3 × 109–2 × 1010 cm−3, with a trend of slightly higher concentrations toward the tail end of each ingot, and in subsequently grown ingots. However, analysis of the effective lifetimes indicates that iron–gallium pairs are not the dominant recombination centers in the as‐grown state. Moreover, when these wafers are subjected to a tabula rasa step, an increase in the iron concentration is observed in the range of 1 × 1010–6 × 1010 cm−3, with iron–gallium pairs becoming the dominant recombination centers. This is possibly caused by the dissolution of pre‐existing precipitated iron in the wafers. Nevertheless, the negative impact of iron contamination can be dramatically reduced by subjecting the wafers to a phosphorus diffusion gettering step, as is commonly incorporated in the fabrication of p‐type passivated emitter and rear cells. Therefore, it is concluded that the quality of the ingots is not limited by iron contamination, even after multiple ingots are pulled from the recharged melt.
We investigated ring defects induced by a two-step anneal in n-type Czochralski-grown silicon wafers using a combination of high spatial resolution Fourier Transform Infrared Spectroscopy (FTIR), micro-photoluminescence (PL) mapping, and micro-Raman mapping. Through FTIR measurements, we show the inhomogeneous loss in interstitial oxygen with a positive correlation with the inverse lifetime. Using high-resolution micro-PL mapping, we are able to distinguish individual recombination-active oxygen precipitates within the rings with a decreasing density from the center to the edge of the sample. The radial inhomogeneity of the oxygen precipitates is likely to be related to variations in the distribution of grown-in defects. We also demonstrate that micro-Raman mapping reveals the oxygen precipitates without the smearing effects of carrier diffusion that are present in micro-PL mapping.
This paper presents experimental studies on the formation of ring defects during high-temperature annealing in both electronic-grade and upgraded metallurgical-grade (UMG) Czochralski-grown silicon wafers. Generally, a faster onset of ring defects, or shorter incubation time, was observed in the UMG samples ([Oi] = 6.3 × 1017 cm−3) in comparison to the electronic-grade samples ([Oi] = 3.9 × 1017 cm−3) used in this work. By applying a tabula rasa (TR) treatment prior to annealing, the incubation time can be increased for both types of wafers. We show that TR temperatures above 1000 °C are necessary to effectively dissolve grown-in oxygen precipitate nuclei and limit the subsequent formation of ring defects. A 30 min TR treatment at 1000 °C resulted in the longest incubation time for both types of samples used in this work, as it achieved the best balance between precipitate nuclei dissolution and precipitate re-growth/ripening. Finally, a nitrogen ambient TR step showed a short incubation time for the formation of ring defects in comparison to an oxygen ambient TR step.