This article describes the first results obtained from the Surface Waves Investigation and Monitoring (SWIM) instrument carried by the China France Oceanography Satellite (CFOSAT), which was launched on October 29, 2018. SWIM is a Ku-band radar with a near-nadir scanning beam geometry. It was designed to measure the spectral properties of surface ocean waves. First, the good behavior of the instrument is illustrated. It is then shown that the nadir products (significant wave height, normalized radar cross section, and wind speed) exhibit an accuracy similar to standard altimeter missions, thanks to a new retracking algorithm, which compensates a lower sampling rate compared to standard altimetry missions. The off-nadir beam observations are analyzed in detail. The normalized radar cross section varies with incidence and wind speed as expected from previous studies presented in the literature. We illustrate that, in order to retrieve the wave spectra from the radar backscattering fluctuations, it is crucial to apply a speckle correction derived from the observations. Directional spectra of ocean waves and their mean parameters are then compared to wave model data at the global scale and to in situ data from a selection of case studies. The good efficiency of SWIM to provide the spectral properties of ocean waves in the wavelength range [70-500 m] is illustrated. The main limitations are discussed, and the perspectives to improve the data quality are presented.

Both Arctic and Antarctic sea ice are affected by climate change. While Arctic sea ice has been declining for several decades, Antarctic sea ice extent slowly increased until 2015, followed by a sharp drop in 2016. Quantifying sea ice changes is essential to assess their impacts on the ocean, atmosphere, ecosystems and Arctic communities. In this study, we combine sea ice thickness estimates from four satellite radar altimeters to derive the longest time series of homogeneous sea ice thickness for both hemispheres over 30 years (1994–2023). The record supports the rapid loss of sea ice in the Arctic for each month of the year and the heterogeneous changes in sea ice thickness in the Antarctic. The study confirms that most of the volume variability is due to the thickness variability, which holds true for both hemispheres. The sea ice thickness time series presented here offer new insights for models, in particular the possibility to evaluate sea ice reanalyses and to initialize forecasts, especially in the Antarctic, where the data set presented here has no equivalent in terms of spatial and temporal coverage.

The accuracy of sea surface parameters retrieved from altimeter missions is predominantly governed by the choice of the so-called “retracking” algorithm, i.e., the model and inversion method implemented to obtain the surface parameters from the backscattered waveform. For continuity reasons, the choice of space agencies is usually to apply the same retracker from one satellite mission to the other to ensure long-time homogeneous series. In this article, taking the opportunity of a new configuration of the nadir pointing measurements onboard the recently launched China France Oceanography Satellite (CFOSAT) with the Surface Waves Investigation and Monitoring (SWIM) instrument (Hauser et al., 2020), the retracking method was upgraded, by implementing a novel algorithm, called “Adaptive” retracker. It combines the improvements brought by Poisson et al., (2018) for the estimation of surface parameters from peaked waveforms over sea ice, improvements in the way the instrumental characteristics are considered in the model (mispointing, point target response) and a more accurate consideration of speckle statistics. In this article, we first show from simulations carried out in the instrumental configuration of SWIM that the Adaptive algorithm has better accuracy and performance than the classical MLE4 algorithm. Then, the geophysical parameters obtained with real data from SWIM are analyzed with comparisons to reference data sets (model and products from altimeters). We show that this new algorithm has several benefits with respect to the classical MLE4 method: no need of lookup tables to correct biases, significant noise reduction on all geophysical variables especially the significant wave height, and performance of inversion over a large set of echo shapes, resulting from standard oceanic scenes as well as highly specular conditions such as over bloom or sea ice.

Satellite altimetry has been providing a continuous record of ocean measurements with numerous applications across the entire range of ocean sciences. A reference orbit has been used since 1992 with TOPEX/Poseidon, which was repeated in the Jason missions, and in the newly launched Sentinel-6 Michael Freilich (in November 2020) to continually monitor the trends of sea level rise and other properties of the sea surface. These multidecadal missions have evolved alongside major technological advances, whose measurements are unified into a single data record owing to continuous intercalibration and validation efforts. However, the new Sentinel-6 provides synthetic aperture radar (SAR) processing, which improves the along-track resolution of conventional altimeters from a few kilometres (e.g., for Jason-3) to about 300 m. This means a major leap in sampling towards higher frequencies of the ocean spectrum, which inevitably means reconciling the assumption of a uniform Brown surface between the footprints of the larger kilometre-scale conventional altimetry and those of the finer-scale SAR altimetry. To explore this issue, this study uses the vantage point of the Sentinel-6/Jason-3 tandem phase to compare simultaneous sea surface signatures of large-scale Internal Solitary Waves (ISWs) between SAR and conventional altimetry. These waves can modulate the sea surface into arrayed sections of increased and decreased roughness with horizontal scales up to 10 km, which inflict sharp transitions between increased and decreased backscatter in the radar altimeters. It is found that Sentinel-6 can provide more detailed structures of ISWs in standard level-2 products, when compared with those from the conventional Jason-3 (similarly to previous results reported from the SAR altimeter from Sentinel-3). However, a new and striking feature is found when comparing the radar backscatter between Sentinel-6 and Jason-3, which are in opposite phases in the ISWs. These intriguing results are discussed in light of the intrinsically different acquisition geometries of SAR and conventional altimeters as well as possible implications thereof.

Seven years (2013–2019) of the French/Indian mission SARAL altimetry data have been successfully reprocessed within the SALP contract supported by CNES to produce a new data set of GDR (Geophysical Data Record) using an updated, modern set of algorithms and models. The main objective of this article is to assess the quality of the reprocessed dataset and estimate the system’s performance using GDR-F products. To achieve this goal, the new dataset has been validated against the previous one (identified as GDR-T) using mono-mission metrics and comparisons to reference altimetry missions such as Jason-2 and Jason-3. The new data set shows a clear improvement in data quality. The product validation shows a reduction of the standard deviation of crossovers’ Sea Surface Height differences from 5.5 cm (GDR-T) to 5.2 cm (GDR-F). This paper presents the main processing changes and shows some of the results from the validation and quality-assurance processes. The major improvement of the GDR-F data set with respect to the previous one is due to the use of state-of-the-art orbit standards (POE-F) and geophysical corrections, including new tidal models, a new wet troposphere retrieval algorithm, and a new algorithm for sea state estimation. The intent of this paper is to highlight the overall benefit of this new dataset.