In view of the gas-liquid two-phase flow process in the oxygen-enriched side-blown molten pool, the phase distribution and manifold evolution in the side-blown furnace under different working conditions are studied. Based on the hydrodynamics characteristics in the side-blown furnace, a multiphase interface mechanism model of copper oxygen-enriched side-blown bath melting was established. The results show that the existence of slag baffle makes the velocity distribution range of melting mixing zone wider, the mixing range of melt wider, the mixing effect better, and the role of melting zone strengthened. The average speed of case MY in the melting zone is the highest, nearly 5.2% higher than that of case EY, and 16.7% higher than that of case EN. Compared with the average turbulent kinetic energy in the melting zone, case MY has a significant advantage of 2.635 m2/s2, which is increased by 47%, 34%, and 14% respectively compared with case EN, case EY, and case MN.
15 December 2022 in International Journal of Chemical Reactor Engineering
The fluid in the reactor can be poorly mixed, so an eccentric impeller is proposed to improve the fluid mixing efficiency. In this investigation, numerical simulations and cadmium removal experiments for the purification of zinc sulfate solution were conducted. The effect of eccentric impellers on the purification efficiency was discussed. The mechanism of the effect of concentric and eccentric arrangement of stirring impellers on mixing in the stirred tank was elucidated. The results showed that the average axial velocity of the eccentric impeller stirring system (EIS) was 131.52% of that of the concentric stirring system (CS) and 134.23% of that of the eccentric stirring system (ES). In the purification and removal of cadmium in the zinc hydrometallurgy experiment, unit ion purification energy was introduced to quantify the energy consumed for each 1% of Cd2+ removed. The eccentric impeller shortens the reaction time by 40% and reduces the reaction energy consumption by 31.8% compared to the non-eccentric impeller. Compared to CS and ES, EIS disrupts the periodicity of fluid flow and facilitates the destruction of isolated mixing regions. EIS can enhance mechanical stirring to improve purification efficiency.
Oxygen lances are key equipment for copper converters. The effect of the lance arrangement on the mixing of a gas–slag two–phase is discussed using numerical simulation and experimental verification with a water model, and the stirring characteristics enhanced by variable–velocity blowing are explored. The results showed that the single–row lance arrangement (SA) increased the average velocity in the slag phase by 17.93% and reduced the disturbance to the metal phase by 27.78% compared to the double–row lance arrangement (DA). Compared to the constant–velocity blowing system (CSB), the sine–wave blowing system (SWB) and rectangular–wave blowing system (RWB) increased the average velocity in the slag phase by 24.03% and 13.96%, respectively, and reduced the proportion of the low–velocity area by more than 46.2%. The velocity imbalance in the SA local area enhances the mixing of the gas–slag two–phase. The variable–speed blowing improves the mass transfer and mixing effect.
19 February 2024 in International Journal of Chemical Reactor Engineering
The hydrodynamic and stirring characteristics of gas-slag-copper matte three-phase in side-blowing melt pool melting were numerically simulated using a combination of the volume of fluid (VOF) model in computational fluid dynamics and the realizable k - ε turbulence model. The study obtained macroscopic flow and gas-liquid two-phase distribution information of the flow field in the melting process. It also examined the effects of isokinetic blowing and nonlinear blowing on the fluid velocity, penetration depth, gas content, and turbulent eddy volume of the flow field, and compared the results. The results indicate that, for the same total gas volume, constant velocity blowing (CVS) inadequately agitates the molten pool, resulting in a large stirring dead zone within the flow field. In contrast, nonlinear blowing enhances the fluid velocity overall. Specifically, sinusoidal variable speed blowing (SWS) and rectangular variable speed blowing (RWS) reduce the stirring dead zone area by 79 and 73.5 %, respectively. This is attributed to the increase in maximum penetration depth and slag phase gas content, as well as the decrease in gas escape during nonlinear blowing. The vortex volume over the total calculated time for the three conditions is enhanced by 6.7 and 1.1 % for SWS and RWS, respectively. Additionally, the turbulent kinetic energy of the fluids is increased by 18.7 and 17 %, respectively.
10 January 2023 in International Journal of Chemical Reactor Engineering
The poor mixing caused by zinc powder deposition in purification process is a serious problem which can’t be avoided in treatment of zinc-containing solid waste. Here, to enhance the purification efficiency of zinc-containing solid waste treatment reactor, two kinds of multi-blade combined stirring systems are compared with single layer four straight-blade and double-layer straight-blade (DFB) stirring systems which are traditionally chosen by industry. This study simulated and explored the flow field characteristics and purification effects of these four kinds of stirred-tank reactor, further proposes the unit ion purification energy (UIPE) as a criterion for purification energy consumption and effect evaluation. The results show that multi-blade combined (MBC) stirring system enhances axial flow by 12.56% in water. Meanwhile it effectively inhibits the growth of isolated mixing region which scope has decreased by 56.25%. In high viscosity Carboxymethylcellulose sodium solution, the fluid axial speed can be increased by up to 1407 times with MBC. MBC can increase the purification rate by 24.79% while the UIPE decreases by 29.45% compared with DFB which is used in industrial purification process. MBC paddle has exhibited a wide range of fluid viscosity applicability and axial velocity improvement effect. The improvement increases collisions between the impurity particles and the zinc powder particles, which increased rate of substitution reactions. The application of MBC solves the purification problem in the process of treating zinc-containing solid waste.