Óscar González-Prieto

Dr. Óscar González-Prieto

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 April 2008 in Drying Technology
Verified
Journal Article
Closed access
CHChristian Hansmann
Christian Hansmann
RSRobert Stingl
Robert Stingl
Óscar González-PrietoÓscar González-Prieto
Óscar González-Prieto
CLCarlos Baso Lopez
Carlos Baso Lopez
HRHelmuth Resch
Helmuth Resch
Worldwide, eucalyptus tree plantations have been established in appropriate climates because of fast growth and wood qualities suitable mainly for pulp. A potential exists of converting eucalyptus trees into lumber that may be of higher value than pulp. Conventional drying of lumber of Eucalyptus globulus is often difficult because of the occurrence of drying stresses, leading to collapse and checking. The special method of vacuum drying while heating the wood with high-frequency energy (75–77 mbar, 46–51°C) was used to obtain short drying times (5–13 days from green state to 10% final moisture content) and low crack amount.

23 February 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Óscar González-PrietoÓscar González-Prieto
Óscar González-Prieto
LTLuis Ortiz Torres
Luis Ortiz Torres
ATAntonio Vazquez Torres
Antonio Vazquez Torres
Using waste biomass is considered one of the ways to reduce climate change. Arboreal waste biomass from pine, eucalyptus, and particularly invasive plants (Acacias) would make it possible to transform this natural resource, but needs to be adjusted to current and innovative technologies. The production of high fixed carbon biochar with this biomass would improve not only environmental aspects, but also the use of currently not susceptible materials for other types of exploitation. The objective of this study is to develop biochar from three different waste biomass materials and compare their parameters with those of the original biomass. Thermochemical conversion processes were used in a simple double chamber reactor developed for this study. Temperatures between 400 and 500 °C during 280 min were achieved and allowed to transform the initial biomass in a biochar with a high content of fixed carbon. By comparing the original biomass with the final biochar through tests of humidity, density, calorific values, fixed carbon, and cationic and elemental analysis, an increase in the parameters was confirmed. Fixed carbon of 70%, 77%, and 71% with pine, acacia, and eucalyptus biomass have been obtained, respectively, with yields between 30% and 40%. The results are favorable, particularly with acacia invasive plants, and could help in their difficult silviculture management.

24 March 2025 in Molecules
Verified
Journal Article
Open access
PDF file
NBNuria Bernárdez
Nuria Bernárdez
Emilio Rosales VillanuevaEmilio Rosales Villanueva
Emilio Rosales Villanueva
Marta PazosMarta Pazos
Marta Pazos
Óscar González-PrietoÓscar González-Prieto
Óscar González-Prieto
LTLuis Ortiz Torres
Luis Ortiz Torres
M. Ángeles SanrománM. Ángeles Sanromán
M. Ángeles Sanromán
The adsorption capacity of a biochar (BC) obtained from pine wood residues was evaluated for its ability to remove two pharmaceuticals: fluoxetine (FLX) and sulfamethizole (SMZ). The material showed promising results in FLX removal, but a limited capacity in the case of SMZ. In order to improve these results, BC surface modifications were made by doping with nitrogen, as well as using acid, basic and electrochemical treatments. A three-dimensional electrosorption treatment proved to be the most effective, increasing the adsorption rate from 0.45 to 13.46 mg/g after evaluating different operating conditions, such as the electrodes used or the BC dosage. Consecutive cycles of BC use were performed through desorption and electro-regeneration techniques to test its capacity for reuse, and it was observed that application in the 25 mA electric field increased the useful life of the material. Finally, the effect of ionic strength was studied, highlighting that the presence of ions did not significantly affect the efficiency of SMZ removal, although a slight increase was observed at a high ion concentration, probably due to a salinization effect.

23 November 2021 in European Journal of Wood and Wood Products
Verified
Journal Article
Open access
PDF file
Óscar González-PrietoÓscar González-Prieto
Óscar González-Prieto
JMJosé Manuel Casas Mirás
José Manuel Casas Mirás
LTLuis Ortiz Torres
Luis Ortiz Torres
The use of glued finger joint in green wood, directly from the sawing process, would open the possibility to obtain glued timber from small-sized wood, achieving an efficient use of the original raw material. The gluing of finger-jointed green wood, with moisture content above the fibre saturation point, may improve the efficiency and the manufacturing process of glulam or joinery. This may be especially beneficial for a hardwood such asEucalyptus globulusL., which is a globally important forest resource, but is a challenging wood to dry. This article presents a study on the possibility to develop finger joints with wood in green state. To compare them, conventional finger joints on dry wood and solid boards without end joints were also manufactured. Cold-setting and fast-curing commercial one-component polyurethane adhesive systems were used. Finger-jointed samples were tested to determine mean and characteristic values (5th percentile) of density, bending strength and modulus of elasticity, and the results were analysed and discussed. Green-glued joints showed no statistically significant differences compared to the solid boards and improved strength properties with respect to dry-glued joints.

19 April 2022 in BioResources
Verified
Journal Article
Open access
YLYeray Manuel López-Gómez
Yeray Manuel López-Gómez
ALAitor Barbero Lopez
Aitor Barbero Lopez
Óscar González-PrietoÓscar González-Prieto
Óscar González-Prieto
MVMartti Venäläinen
Martti Venäläinen
Antti HaapalaAntti Haapala
Antti Haapala

30 July 2025 in Biomass
Verified
Journal Article
Open access
PDF file
Óscar González-PrietoÓscar González-Prieto
Óscar González-Prieto
LTLuis Ortiz Torres
Luis Ortiz Torres
MCMaría Esther Costas Costas
María Esther Costas Costas
The feasibility of utilizing biochar as a static floating material for agricultural applications was researched to prevent evaporation from open water static storage systems or as a floating barrier in slurry pits, for instance. Five types of biochar were created from chips, bark, and pellets of pine and residues from two acacia species using a pyrolysis time between 60 and 120 min and mean temperatures between 380 and 690 °C in a simple double-chamber reactor. Biomass and biochar were characterized for their main properties: bulk density, moisture content, volatile matter, ash content, fixed carbon, and pH. Biochar was also evaluated through a basic floatability test over 27 days (648 h) in distilled water. The highest fixed carbon content was observed in pine bark biochar (69.5%), followed by the pine pellets (67.4%) and pine chips (63.4%). Despite their high carbon content, the pellets exhibited a low floatability level, whereas pine bark biochar showed superior static floatage times, together with chip and ground chip biochar. These results suggest that biochar produced from bark and wood chips may be suitable for application as floatability material in water or slurry management systems. These results warrant further research into the static floating of biochar.