The constantly growing number of vehicles sold and operated has resulted in greater contribution of automobiles to global pollution. One way to reduce emissions of carbon dioxide (CO2) and toxic compounds, including the particulates and nitrogen oxides (NOx) contained in exhaust gases, is to use alternative fuels. Within this group of fuels, those of plant origin, mainly alcohols, are attracting more and more attention because of their high oxygen content (around 35%), low viscosity, and good atomisation. However, alternative fuels have different physicochemical properties than diesel fuel, and these may affect the formation of the fuel spray, which, in turn, impacts the operation of the internal combustion engine, operating parameters, and the purity of the exhaust gases emitted into the environment. To make sure this type of fuel can be used in compression ignition engines, it is necessary to gain a thorough understanding of the phenomena and relationships occurring during fuel injection. The study investigated the effect of ethanol added to diesel fuel on the range of fuel spray. Firstly, the kinematic viscosity was determined for diesel fuel, and for diesel–ethanol blends with varying proportional contents of ethanol, up to 30% v/v. The viscosity test was carried out at 40 °C in compliance with the normative requirements. At the next stage, the range of the spray tip was measured for the same fuels in which kinematic viscosity was assessed. A visualisation chamber and a high-speed camera were applied for this purpose. The test was carried out under reproducible conditions, in line with the test methodology used to determine the range of fuel spray. The analyses assessed the effect of ethanol addition on kinematic viscosity and the range of fuel spray. The findings show that the increase in ethanol content corresponds to a decrease in kinematic viscosity by about 4% on average. The results were inconclusive for the lowest injection pressure tested (75 MPa), since some of the mixtures investigated were found with a lower spray range, compared to diesel fuel with no ethanol added. The greatest increase in the spray range (by approximately 39%) was found in the fuel with 30% content of ethanol at an injection pressure of 125 MPa.
The search for alternative liquid fuels for compression-ignition (CI) internal combustion engines includes waste-derived fuels such as hydrotreated vegetable oil (HVO) and pyrolytic oils from end-of-life tires (tire pyrolytic oil, TPO) and plastics—polystyrene pyrolytic oil (PSO). The application of these fuels requires meeting a number of criteria, including exhaust pollutant emissions. The scientific objective of this study was to compare pollutant emissions—carbon dioxide (CO2), carbon monoxide (CO), total hydrocarbons (THC), nitrogen oxides (NOx), particulate matter (PM)—and fuel consumption of a passenger car CI engine fueled with diesel B7, HVO, and a blend consisting of 90% HVO, 5% TPO, and 5% PSO (vol.), hereinafter referred to as HVO–TPO–PSO. The tests were carried out using a chassis dynamometer equipped for conducting standardized WLTC Class 3b driving cycles, with exhaust gases measured by laboratory-grade analyzers to ensure accuracy and repeatability. Fueling the engine with HVO resulted in the lowest CO2, CO, THC, NOx, and PM emissions across all phases of the driving cycle. The addition of pyrolytic oils to HVO increased NOx and CO2 levels while maintaining benefits in PM, THC, and CO reduction compared to the B7 reference fuel. The results demonstrated the applicability of HVO–TPO–PSO blends in engine applications while indicating the need for further durability studies. The adopted research approach addresses a significant knowledge gap by providing a unique analysis of the impact of HVO blends with tire and plastic pyrolysis oils on pollutant emissions and internal combustion engine fuel consumption under WLTC 3b operating conditions.
The article presents the development and results of emission studies conducted in Poland in the context of global real-driving emissions research. Although the European Union has continuously tightened exhaust-emission standards, road transport remains one of the major sources of air pollution. Several research centers in Poland—including Rzeszów University of Technology, Poznan University of Technology, and the Motor Transport Institute—have been conducting on-road emission measurements for many years across a wide spectrum of vehicles: conventional, hybrid (including plug-in hybrids), and fully electric. The findings show that emissions under real-world driving conditions often differ from those obtained in homologation tests, particularly for nitrogen oxides and particulate matter. Ambient temperature, road gradient, and driving phases (urban, rural, motorway) were also identified as influential factors. Polish research centers have developed analytical tools enabling comparison between laboratory and on-road tests and allowing real-driving emissions to be estimated based on chassis-dynamometer data. Studies on plug-in hybrids highlighted that these vehicles remain environmentally beneficial only when regularly charged; otherwise, their emissions can increase sharply. Overall, the research confirms that on-road testing is essential for a reliable evaluation of vehicle performance, and the results can contribute to designing more eco-friendly technologies and improving future emission regulations.
The internal combustion engine continues to be the main source of power in various modes of transport and industrial machines. This is due to its numerous advantages, such as easy adaptability, high efficiency, reliability and low fuel consumption. Despite these beneficial qualities of internal combustion engines, growing concerns are related to their negative environmental impacts. As a result, environmental protection has become a major factor determining advancements in the automotive industry in recent years, with the search for alternative fuels being one of the priorities in research and development activities. Among these, fuels of plant origin, mainly alcohols, are attracting a lot of attention due to their high oxygen content (around 35%). These fuels differ from diesel oil, for instance, in kinematic viscosity and density, which can affect the formation of the fuel spray and, consequently, the proper functioning of the compression–ignition engine, as well as the performance and purity of the exhaust gases emitted into the environment. The process of spray formation in direct injection compression–ignition engines is extremely complicated and requires detailed analysis of the fast-changing variables. This explains the need for using complicated research equipment enabling visualisation tests and making it possible to gain a more accurate understanding of the processes that take place. The present article aims to present the methodology for alternative fuel visualisation tests. To achieve this purpose, sprays formed by diesel–ethanol blends were recorded. A visualisation chamber and a high-speed camera were used for this purpose. The acquired video provided the material for the analysis of the changes in the vertex angle of the spray formed by the fuel blends. The test was carried out under reproducible conditions in line with the test methodology. The shape of the fuel spray is impacted by an increase in the proportional content of ethanol in the diesel and dodecanol blend. Based on the present findings, it is possible to note that the values of the vertex angle in the spray produced by the diesel–ethanol blend with the addition of dodecanol are most similar to those produced by diesel oil at an injection pressure of 100 MPa. The proposed methodology enables an analysis of the injection process based on the spray macrostructure parameters, and it can be applied in the testing of alternative fuels.
The article presents findings of the comparative analyses of the selected physicochemical parameters of diesel fuel and diesel-ethanol blends with addition of dodecanol, used in order to stabilise the blend Diesel fuel and the blends were tested for density, flash point and cold filter plugging point. The physicochemical propertis were assessed in seven samples with different proportional volume of ethanol contained in diesel fuel. Homogeneous blends were produced by adding 5% dodecanol to blends containining between 5% and 30% ethanol. The study was conducted to assess the selected physicochemical properties of diesel-ethanol blends with addition of dodecanol and to compare the obtained results with requirement of EN590:2022-08
The use of alternative fuels and fuel components derived from organic and inorganic waste enables progress toward the goals set by decarbonization policies and environmental protection, but on the other hand, it presents a number of challenges related to maintaining the operational quality of these fuels. This primarily involves achieving normative physico-chemical parameters for newly formulated blends intended for powering automotive engines, as well as identifying and effectively removing both solid and liquid contaminants specific to each fraction (component). Information concerning the chemical composition and purity of individual fuel components is essential in the context of formulating substitute fuels. This article presents the results of comparative studies on the amount of contaminants found in substitute fuel components such as hydrotreated vegetable oil (HVO), tire pyrolysis oil (TPO), and plastic-derived pyrolysis oils – polypropylene pyrolytic oil (PPO) and polystyrene oil (PSO). For diesel fuel and substitute fuels, microfiltration was carried out using membrane filters to determine the quantity of solid impurities. The aim of the study was to assess the feasibility of using these types of fuels either on their own or in blends with diesel fuel, under the assumption that they would be used directly after processing to power compression ignition engines. The research showed that the distillation process of pyrolytic oils significantly reduces the content of process-related impurities. The greatest reduction was observed for PPO, where after filtering a 50 ml sample the level of contaminants after distillation and ashing decreased from approximately 23 mg to a value close to zero.