Following the Great East Japan Earthquake, a massive tsunami caused serious damage to coastal dikes. Local scour at the ground behind these dikes reportedly causes dike failures. It is important to reveal the scour process to establish methods for effective scour countermeasures. Herein, we focus on geogrids. To verify this proposal and examine its design, flume-model experiments were performed for non-liquefied and liquefied grounds behind coastal dikes. The results showed that the scour amount and area were reduced drastically when geogrids were present. Geogrids on the sand-bed surface changed the direction of overflow water. Thus, a scour hole developed away from a coastal dike model. Furthermore, geogrids exerted a scour-reduction effect even during liquefaction.
Metrological traceability is essential to ensure the reliability of calibration tests. Calibration certificates usually include information on only one upper-level reference standard. As metrological traceability is multi-layered, generally there is no method available for end users to instantly confirm the traceability from the reference standard to a primary standard. This study focuses on the Ethereum blockchain, which has both tamper resistance and high availability, as a digital data management method. To improve the transparency and reliability of calibration tests, a smart contract that traces back to the primary standard is proposed. Consequently, it is confirmed that end users can instantly obtain traceability information. In addition, the execution of smart contracts requires transaction fees. Here, the calculation of the transaction fees is organized, and the traceability management system is discussed from a cost-effective perspective in the field of metrology.
In flow velocity measurements, resolution, miniaturization, and accuracy of measuring devices are important issues because the measuring devices significantly affect the flow in the micro-space, sonic flow, and turbulent flow. We studied recovery temperature anemometry (RTA) using micrometer-order thermometers and evaluated its validity in two velocity ranges (40–90 and 315–420 m/s) by conducting two experiments and a numerical simulation. The results confirmed that the difference between the reference velocity and RTA was within 5% in the velocity range 60–90 m/s for both the thermocouple and platinum thermometer given the same recovery temperature coefficient of 0.83. It is a valuable finding that velocity measurement by RTA is independent of the type of thermometer used. This suggests that the accuracy of about 5% can be guaranteed even without calibration by giving the recovery temperature coefficient according to the thermometer geometry, which is an excellent advantage not found in other anemometers. Furthermore, the supersonic flow measured using RTA agrees well with the simulation results and theoretical trends. Our findings ensure that the micrometer-order point measurement of flow velocity, which is difficult with existing anemometers, using RTA is possible over a wide range of flow velocities.
24 October 2016 in International Journal of Geotechnical Engineering
In the present study, hydraulic model experiments were conducted to clarify the influence of liquefaction on the scour behind coastal dikes due to tsunami overflow. In particular, the variation of the scour profile (scour depth, scour length and scour area) due to liquefaction was discussed. Degree of liquefaction was controlled by upward seepage, which was induced by the head difference between a water tank and a sand bed. Six hydraulic gradients were applied to the sand bed. The experimental results showed that liquefaction had a significant impact on the scour profile. At high hydraulic gradient, slope failures occurred due to reduction of effective stress of the sand bed. As a result, scour length was increased by the slope failures. Furthermore, the maximum scour depth and scour area for high hydraulic gradient became smaller than that for low hydraulic gradient.
28 January 2024 in International Journal of Hydrogen Energy
Coastal dikes are an essential social infrastructure to mitigate tsunami damage. However, there are no clear guidelines on effective dike shapes for reducing tsunami overflow. To examine effective dike shapes, numerical simulations of the amount of tsunami overflow at coastal dikes are conducted with reference to tsunami waveforms caused by the Great East Japan Earthquake. Results reveal the relationship between the dike shape and the amount of the overflow; the mechanism of overflow reduction based on the velocity and water level distribution is also verified. The comparison of the seaward and landward slopes of coastal dikes reveals that the seaward slope has a greater impact on the overflow, and the seaward slope with a vertical wall or a wave return structure reduces the overflow by 5%–30% compared to the 1:2 (26.6°) seaward slope. The landward slope should be determined based on the tsunami scale and the scour related to the dike stability. Since tsunami inflow damages human life and social infrastructure, achieving the overflow reduction without increasing dike height is vital. Our work contributes to rational design guidelines for coastal dikes.