The main objective of this research is to identify optimal printing strategies and PLA (polylactic acid) filament materials to produce rapid prototype deep drawing tools. Additive 3D printing technologies have been applied for a long time to produce tools, but the research is unique in that it uses conventional and various reinforced PLA materials with conventional FDM (Fused Deposition Modeling) printers. The advantage of this method is that PLA is easy to print and recycle and does not require expensive or special printers, this also gives the article its novelty. A further aim was to produce the tools using commercially available low-end printers. DX53D 0.8 mm thick body steel and AlMg3 2.5 mm thick sheet were the materials to be molded for the tests. The test tool was an Erichsen deep drawing punch. Tool wear was tested using the GOM ATOS measuring system, an optical coordinate measuring machine based on the DIC (Digital Image Correlation) principle, which is also popular in the automotive industry. The study aims to determine the 3D printing and material parameters that can safely produce a minimum batch of 100 parts.

This article summarizes the research results related to our own conducted extensive laboratory tests of polymer composite and steel fishplated glued insulated rail joints (GIRJs), namely axial tensile tests as well as vertical static and dynamic tests. The investigation dealt with the examination of GIRJs assembled with steel and special glass-fiber reinforced plastic (polymer composite) fishplates, both of them for CWR railway tracks (i.e. so-called gapless tracks or, in other words, railway tracks with continuously welded rails). The exact rail joint types were MTH-P and MTH-AP, consistently. The MTH P types have been commonly applied for many years in the CWR tracks in Europe, mainly in Hungary. The MTH-AP rail joints consist of fishplates that are produced by the APATECH factory (Russia). They are made of a fiberglass-amplified polymer composite material at high pressure and controlled temperature. This solution can eliminate electrical fishplate lock and early fatigue failures just as it can ensure adequate electrical insulation. The advantage of such rail joints can be that they are probably able to ensure the substitution of the glued insulated rail joints with relatively expensive steel fishplates currently applied by railway companies, e.g. Hungarian State Railways (MÁV). The aim of the mentioned research summarized in this paper is to formulate recommendations on technical applicability and on the technological instructions that are useful in everyday railway operation practice on the basis of the measurements and tests carried out on rail joints in laboratory.

The preparatory operations of DIC (Digital Image Correlation) tests were investigated in this study, with special emphasis on specimen cleaning and painting operations. As it is well known, DIC tests are non-contact and applied in materials research, the analysis of complex structures, and, nowadays, the construction industry. The use of DIC technologies has seen a dynamic increase in all scientific fields. In our study, aluminum body panels for automotive and railway applications were tested using this technique. There are many articles on proper patterning in the literature but fewer on preparation and priming. These are critical for a successful DIC measurement. This paper looks at different surface cleaners and primers with different grading procedures and will also determine the time window within which the paint should be applied. Finally, the GOM ARAMIS system was applied to measure and characterize the painted surface and visible deformation defects resulting from inadequate painting.

This research investigates the application of plastic fiber reinforcement in pre-tensioned reinforced concrete railway sleepers, conducting an in-depth examination in both experimental and computational aspects. Utilizing 3-point bending tests and the GOM ARAMIS system for Digital Image Correlation, this study meticulously evaluates the structural responses and crack development in conventional and plastic fiber-reinforced sleepers under varying bending moments. Complementing these tests, the investigation employs ABAQUS’ advanced finite element modeling to enhance the analysis, ensuring precise calibration and validation of the numerical models. This dual approach comprehensively explains the mechanical behavior differences and stresses within the examined structures. The incorporation of plastic fibers not only demonstrates a significant improvement in mechanical strength and crack resistance but paves the way for advancements in railway sleeper technology. By shedding light on the enhanced durability and performance of reinforced concrete structures, this study makes a significant contribution to civil engineering materials science, highlighting the potential for innovative material applications in the construction industry.

The article deals with DIC (Digital Image Correlation) tests on steel plates used in the automotive and railway industries, as well as in the construction industry. The most critical part of DIC tests is the quality of proper surface preparation, painting, and random patterns. The paint mediates the deformation of the optical systems, and its quality is paramount. The authors’ goal in this research is to determine the optimal dye–cleaning–drying time parameters for DIC studies. Commercially available surface preparation and cleaning agents were tested alongside commercially available spray paints. Standard and specific qualification procedures were applied for the measurements. Once the appropriate parameters were determined, the results were validated and qualified by GOM ARAMIS tests. Based on the results, DIC measurements can be performed with higher accuracy and safety in laboratorial and industrial conditions, compared to the traditional deformation measurements executed by dial gauges or linear variable differential transformers.

We investigated lubricants and thin teflon foils that can be applied in the formability testing of the thin aluminum sheets used in the electronics and automotive industries. For the tests, thirteen different industrial lubricants (oils and greases) (i.e., L1–L13) and two Teflon films (i.e., 0.08 and 0.22 mm thick) were applied. The authors conducted an Erichsen test, and the thickness reduction of the discs was measured first. In forming-limit curve (FLC) tests, it is crucial that the stresses are localized in the central area of the specimen during forming and that biaxial deformation is maintained throughout, if possible. We aimed to achieve and fulfill this task. To perform this measurement, the GOM ARAMIS measuring system was utilized. It is an optical measuring system based on the digital image correlation (DIC) principle, capable of measuring both stresses and displacements in real time. A specific validation method was also developed to qualify the DIC system. We concluded that there was a 5% difference in Erichsen indentation (IE) number diagrams between the best (L12) and worst (L4) cases for the lubricants and oils tested, which is a significant difference for thin plates. We found that this value could be increased and improved by using Teflon discs. Furthermore, the localization of stress maxima, i.e., the centering of cracks in the specimen, could be achieved by combining Teflon discs and L12 lubricant (with appropriate layer order), which significantly aids in the recording of standard FLC diagrams. Using foils is also advantageous because they are readily available, have no expiry date, and are of less environmental concern.