Reactivity-Controlled Compression Ignition (RCCI) combustion is considered one of the most promising Low-Temperature Combustion (LTC) concepts aimed at reducing greenhouse gases for the transportation and power generation sectors. Due to the spontaneous combustion of a lean, nearly homogeneous mixture of air and low-reactivity fuel (LRF), ignited through the direct injection of a small quantity of high-reactivity fuel (HRF), RCCI (dual-fuel) shows higher efficiency and lower pollutants compared to conventional diesel combustion (CDC) if run at very advanced injection timing. Even though a HRF is used, the use of advanced injection timing leads to high ignition delays, compared to CDC, and generates high cycle-to-cycle variability, limited operating range, and high pressure rise rates at high loads. This work presents an experimental analysis performed on a heavy-duty single-cylinder compression ignited engine in dual-fuel diesel–natural gas mode. The objective of the present work is to investigate and highlight the correlations between combustion behavior and pollutant emissions, especially unburned hydrocarbons (HC) and oxides of nitrogen (NOx). Based on the analysis of crank-resolved pollutants measurements performed through fast FID and fast NOx systems under different engine operating conditions, two correlations were found demonstrating a good accordance between pollutant production and combustion behavior: Net Cyclic Hydrocarbon emission—cyclic IMEP variations (R2 = 0.86), and Cyclic NOx—maximum value of the Rate of Heat Released (R2 = 0.82).
Dual fuel combustion leverages a high-reactivity fuel (HRF) to ignite a premixed low reactivity fuel (LRF)–air mixture to achieve high efficiencies and low engine-out emissions. The difference in the relative amounts of these fuels and in-cylinder fuel reactivity stratification profoundly impacts dual fuel combustion. The effect of increasing LRF energy substitution on dual fuel combustion at various fixed HRF (diesel) quantities was experimentally studied for two different LRFs (natural gas and propane) on a heavy-duty single cylinder engine at a constant intake pressure of 1.5 bar and injection pressure of 500 bar. Further, this effect was studied for three different HRF start of injection (SOI) timings of 310 CAD (50° BTDC), 330 CAD (30° BTDC), and 350 CAD (10° BTDC). For 310 CAD SOI, increasing the LRF substitution at a fixed HRF resulted in higher loads, peak cylinder pressures, and peak apparent heat release rates (AHRR). The onset of low temperature heat release (LTHR) was advanced as the LR fuel flowrate increased at a given pilot quantity for diesel–NG but remained constant for diesel–propane dual fuel combustion at these SOIs due to the impact of propane on the temperature at which the onset of LTHR occurs. The indicated fuel conversion efficiency (IFCE) ranged from 35% at 4 bar IMEPg to 47% at 9 bar IMEPg with NG as the LRF and from 35% at 3 bar IMEPg to 51% at 8 bar IMEPg with propane as the LRF. For 330 CAD SOI, the HC and CO emissions decreased at a higher fixed HRF quantity and an increasing LRF substitution. However, this was accompanied by significantly higher oxides of nitrogen (NOx) emissions for both NG and propane as LRFs. For 350 CAD SOI, increasing the LRF substitution at constant HRF consistently led to a higher second stage AHRR, whereas the first stage AHRR remained relatively unchanged for both NG and propane as LRFs. This was accompanied by higher IFCE for all fixed HRF quantities as LRF substitution was increased. For all SOIs studied, the HC and CO emissions were substantially lower and combustion stability was significantly improved as the LRF substitution (and consequently, the load) was increased. To the best of the authors’ knowledge, the present work is unique in that it involves the first systematic experimental study of the impact of LRF energy substitution at fixed HRF quantities over a range of SOIs, providing comparative results for two different LRFs (NG and propane) on the same engine platform.
Dual-fuel low-temperature combustion is a possible solution for alleviating the tradeoff between oxides of nitrogen and soot emissions in conventional diesel combustion, albeit with poor combustion stability, high carbon monoxide, and unburned hydrocarbon emissions at low engine loads. The present work compares emissions and combustion (heat release and other metrics) of both diesel and poly-oxy methylene dimethyl ether as high-reactivity fuels to ignite natural gas while leveraging spray-targeted reactivity stratification, which involved multiple injections of the high-reactivity fuels. The experiments included six parametric sweeps of: (1) start of first injection, (2) start of second injection, (3) percentage of energy substitution of natural gas, (4) commanded injection duration ratio, (5) rail pressure, and (6) intake pressure. The experiments were performed on a 1.8 L heavy-duty single-cylinder research engine operating at a medium speed of 1339 rev/min. Not-to-exceed limits for the indicated oxides of nitrogen emissions, maximum pressure rise rate, and the coefficient of variation of the indicated mean effective pressure were set to 1 g/kWh, 10 bar/CAD, and 10%, respectively. The indicated emissions decreased and combustion improved significantly for both fueling combinations when the experimental procedure was applied.
31 August 2023 in Journal of Engineering for Gas Turbines and Power
Cyclic variations in internal combustion engines are caused by various factors, including combustion mixture stratification, in-cylinder flows, local fluctuations in air-fuel ratio, etc. Cyclic variations have a profound impact on engine performance and emissions. In this study, cyclic variations in dual fuel combustion are analyzed, comparing diesel–natural gas (NG) and polyoxymethylene dimethyl ether (POMDME)-NG dual fuel combustion. Cyclic variability was initially quantified using the coefficient of variation of gross indicated mean effective pressure (IMEPg) computed from experimental cylinder pressure data. The cases analyzed in this study had a coefficient of variation (COV) of IMEPg greater than or around 5%, which was the lower limit of onset of instability for this engine. Experiments were performed at two fixed start of injection (SOI) of high-cetane fuel: 310 CAD and 350 CAD. For all experiments, a constant load of 5 bar IMEPg was maintained, and the intake boost pressure and rail pressure were fixed at 1.5 bar and 500 bar, respectively. For each case, 1000 cycles of cylinder pressure data were recorded, filtered, and processed using an in-house heat release analysis code for each cycle. A comparison between individual cycles and the “ensemble averaged cycle” was made for both diesel–NG and POMDME–NG combustion. For the early SOI of 310 CAD, the peak cylinder pressure fluctuations of individual cycle were found to be ± 15 bar for both fuel combinations, compared to the ensemble averaged cycle, and < 1/10th of the cycles had an IMEPg lower than 0.05 bar of the ensemble averaged cycle. However, the peak pressure fluctuations were found to be lower for POMDME–NG (±3 bar) than diesel–NG dual fuel combustion at 350 CAD SOI, indicating lower cyclic variations. The higher reactivity of POMDME helped reduce fluctuations in combustion phasing at the retarded SOI. The presence of cycles of deterioration and cycles of recovery were also observed with diesel–NG combustion for 310 CAD SOI, and the scatter in the IMEPg return map was similar for both fuel combinations. The IMEPg return map for POMDME–NG combustion was less scattered at the 350 CAD SOI.
Dual fuel engines utilize two different fuels consisting of a high reactivity fuel (HRF) injected into the cylinder and a low reactivity fuel (LRF), typically fumigated into the intake manifold. To reduce engine-out emissions of oxides of nitrogen (NOx), early start of injection (SOI) of HRF may be employed in dual fuel combustion, albeit at the expense of higher engine-out emissions of unburned hydrocarbons (HC) and carbon monoxide (CO). This study compares performance and emissions of diesel–propane and poly-oxy methylene dimethyl ether (POMDME)-propane dual fuel combustion for a heavy-duty single-cylinder research engine (SCRE) platform based on a production PACCAR MX-11 engine at a low load of 5 bar IMEPg and a constant speed (“B Speed”) of 1339 rpm. While POMDME-natural gas combustion has been explored in previous work, the novelty of the present work lies in the direct comparison of diesel–propane and POMDME–propane combustion for the same SCRE under fixed constraints of NOx < 1 g/kWh, COV of IMEP < 5%, and a maximum pressure rise rate < 10 bar/CAD. By optimizing HRF injection parameters, boost pressure, and propane energy substitution, the present work demonstrates diesel–propane HC and CO emissions improvements of ~86% and ~67%, respectively, while POMDME–propane HC and CO emissions improved by ~91% and ~86% respectively, compared to the corresponding unoptimized baseline values. These improvements were obtained while achieving very low engine-out NOx emissions (diesel–propane ~0.7 g/kWh, POMDME–propane ~0.1 g/kWh) and very good gross indicated fuel conversion efficiencies (diesel–propane ~51%, POMDME–propane ~48%). Additionally, POMDME–propane demonstrated near-zero measurable smoke emissions for all engine operating conditions.