The article presents results of investigations on autogenous laser welding of new grade STRENX 1100 MC steel. The modern Disk laser was applied for of 5.0 mm thick butt joints welding. The influence of laser welding parameters, mainly the energy input of laser welding on the penetration shape, weld quality, structure and mechanical performance was investigated. It was found that the investigated steel has surprisingly low carbon equivalent CET just 0.328, and also relatively high temperature of martensitic transformation Msat 430.6°C. Despite very rapid cooling times t8/5in a range from 0.6 to 1.3 s, thus rapid solidification there was no tendency to cracking of weld metal or HAZ. Significant drop of microhardness in the HAZ resulted in a decrease of tensile strength of joints, compared to the base metal. Impact toughness of test joints was at only 50÷60% of the base metal.
This article presents the results of a study on the laser cladding of metal matrix composite coatings using an experimental custom-made powder composed of NiCrBSi matrix with 65 wt.% reinforcing hard particles of eutectic WC + W2C. The chemical and phase composition of the powder was designed to ensure high hardness, abrasion wear resistance at moderate dynamic loads and corrosion resistance at high temperature of the coatings. The influence of the basic processing parameters of the laser cladding, especially energy input, on the quality and single bead geometry, the dilution, share of the massive carbides in the matrix, and the fraction share of reinforcing carbides particles on cross-section of the clads, as well as hardness profiles and abrasive wear resistance, were analysed and presented. The microstructure of test coatings, chemical and phase composition were analysed by optical and scanning electron microscopes (OM, SEM), EDS and XRD spectrometers. It was found that the differences in the wear resistance of the coatings produced at different energy inputs of laser cladding were directly related to the share of the massive carbides WC + W2C in the metal matrix NiCrBSi. The tribological characteristics of the coatings were also studied and described. The test results indicate that the coefficient of friction for carbides is slightly higher than for the metal matrix, and therefore the greater the share of carbides, the higher the value of the coefficient of friction of the coating.
13 April 2018 in Archives of Metallurgy and Materials
The automated laser welding process of 2.0 mm thick sheets of AISI 304 stainless steel was investigated. The disk laser with a beam spot diameter of 200 μm was used for bead-on-plate and next for autogenous butt joints welding. The influence of basic welding parameters such as laser power, welding speed, and focal spot position on fusion zone configuration, quality of joints, microstructure changes, and microhardness distribution across the joints were analysed and presented in this paper. The results have shown that stiffening of the 2.0 mm thick sheets is crucial for providing high quality and reproducibility of butt joint in a case of AISI 304 stainless steel due to relatively low thermal conductivity and simultaneously high thermal expansion. Relevant drop of microhardness in the weld zone was observed. The mean value of microhardness of the base metal was 230 HV0.1, while the microhardness in fusion zone of the test welds was ranged from 130 to 170 HV0.1. Additionally the microstructure changes in the weld metal and also in the heat affected zone of test joints is described.
1 January 2020 in Journal of Achievements in Materials and Manufacturing Engineering
Purpose: of this paper was to analyze the influence of the basic parameters of laser welding (i.e. laser beam power and welding speed, as well as energy input) of butt joints of the 2.0 mm thick stainless steel AISI 304 sheets on the weld shape and joint quality. Design/methodology/approach: The preliminary trials of simulated laser welding by melting the austenitic stainless steel sheets (the so called bead-on-plate welding), as well as the welding of the test butt joints, were carried out using the high-power diode laser (HPDL) ROFIN DL 020, without the additional material (the technique of autogenous welding). A crucial parameter that determines both the mechanical properties and the corrosive resistance of a joint (the region of a weld and HAZ - heat affected zone) in the case of stainless steels with austenitic structure is energy input, which should be kept at a minimum, and at the same time full penetration and a proper shape of the fusion zone should be ensured. The investigations included the macrostructure and microstructure observations by light microscopy, researches of mechanical properties in a static tensile test and also microhardness measurements made by Vickers method. Findings: The results have shown that it is possible to provide a proper shape of the weld of fine-grained structure and narrow heat affected zone, but it requires careful selection of the welding parameters, especially a low energy input. The microhardness measurements showed that the in case of welding the butt joints using the high-power diode laser in HAZ area a slight increase in microhardness to approx. 185HV0.2 compared to base material (160-169HV0.2) and a decrease in microhardness in the fusion zone (FZ) to approx. 140- 150HV0.2 have been observed. All welded sample broke from the joint during the testing at tensile stress between 585 MPa and 605 MPa with corresponding percentage elongation in the range of 45-57%. It can be found that the joints strength is not less than the strength of the base metal of 2.0 mm thick AISI 304 austenitic stainless steel sheet. Research limitations/implications: Studies of the weldability of stainless steels indicate that the basic influence on the quality of welded joints and reduction of thermal distortions has the heat input of welding, moreover the highest quality of welded joints of austenitic stainless steel sheets are ensured only by laser welding. Practical implications: The laser welding technology can be directly applied for welding of austenitic steel AISI 304 sheets 2.0 mm thick. Originality/value: Application of high power diode laser for welding of austenitic stainless steel AISI 304.