To improve the performance and increase the lifetime of oil‐filled transformers, the thermal and dielectric properties of the transformer oil should be enhanced. Recently, nanotechnology was used as an effective science in the field of transformer oil development. In this study, barium titanate (BT) nanoparticles were inserted into the base transformer oil by a concentration of 0.005 g/L as an individual nanofluid sample (INFS). This insertion enhances the heat transfer coefficient by 33% but the breakdown voltage (BDV) was decreased by >10%. To overcome this problem of dielectric properties degradation, other three hybrid nanofluid samples (HNFS) were prepared using three different types of metal oxide (MO) nanoparticles; titania, alumina, and silica. These samples were prepared by adding a concentration 0.01 g/L of MO nanoparticles together with 0.005 g/L of BT nanoparticles into the oil. The thermal and dielectric properties of HNFS were measured to study the behaviour of nanoparticles hybridisation on transformer oil properties. HNFS using titania nanoparticles provided the best composition regarding either BDV or heat transfer coefficient. Dynamic light scattering (DLS) technique was used to evaluate the particle size distribution of hybrid nanoparticles and to clarify the corresponding physical mechanisms behind the obtained enhancement.

Mineral oil (MO) is the most popular insulating liquid that is used as an insulating and cooling medium in electrical power transformers. Indeed, for green energy and environmental protection requirements, many researchers introduced other oil types to study the various characteristics of alternative insulating oils using advanced diagnostic tools. In this regard, natural ester oil (NEO) can be considered an attractive substitute for MO. Although NEO has a high viscosity and high dielectric loss, it presents fire safety and environmental advantages over mineral oil. Therefore, the retrofilling of aged MO with fresh NEO is highly recommended for power transformers from an environmental viewpoint. In this study, two accelerated aging processes were applied to MO for 6 and 12 days to simulate MO in service for 6 and 12 years. Moreover, these aged oils were mixed with 80% and 90% fresh NEO. The dielectric strength, relative permittivity, and dissipation factor were sensed using a LCR meter and oil tester devices for all prepared samples to support the condition assessment performance of the oil mixtures. In addition, the electric field distribution was analyzed for a power transformer using the oil mixtures. Furthermore, the dynamic viscosity was measured for all insulating oil samples at different temperatures. From the obtained results, the sample obtained by mixing 90% natural ester oil with 10% mineral oil aged for 6 days is considered superior and achieves an improvement in dielectric strength and relative permittivity by approximately 43% and 48%, respectively, compared to fresh mineral oil. However, the dissipation factor was increased by approximately 20% but was at an acceptable limit. On the other hand, for the same oil sample, due to the higher molecular weight of the NEO, the viscosities of all mixtures were at a higher level than the mineral oil.

Recently, significant efforts have been exerted to replace mineral oil with environmentally friendly oils due to safety and environmental issues. However, there is a need to clarify the physical mechanisms behind the ageing impact of these oils. The authors use advanced optical spectroscopy techniques in correlation with dielectric measurements to understand the ageing processes in environmentally friendly oils as well as mineral oil. Firstly, different samples of environmentally friendly oils and mineral oil were utilised to investigate the ageing mechanism. The samples were subjected to different ageing periods using a thermal accelerated ageing process. Secondly, the severity of the produced byproducts due to the oil degradation is examined based on several measured properties representing macroscopic and microscopic categories. The macroscopic category was evaluated through dielectric properties, including breakdown voltage, dielectric permittivity, and dissipation factor. The microscopic category, on the other hand, was assessed using techniques such as ultraviolet–visible absorption spectroscopy and photoluminescence spectroscopy. These techniques enabled a deep understanding of the molecular‐level changes occurring in the oil under ageing conditions, thereby getting new insights into oil ageing mechanisms. It is worth mentioning that natural ester oil demonstrated the most favourable performance across various properties under ageing conditions.

The enhancement of the thermal properties of insulating oils has positively reflected on the performance of the electrical equipment that contains these oils. Nanomaterial science plays an influential role in enhancing the different properties of liquids, especially insulating oils. Although a minimum oil circuit breaker (MOCB) is one of the oldest circuit breakers in the electrical network, improving the insulating oil properties develops its performance to overcome some of its troubles. In this paper, 66 kV MOCB is modeled by COMSOL Multiphysics software. The internal temperature and the internally generated heat energy inside the MOCB during the making process of its contacts are simulated at different positions of the movable contact. This simulation is introduced for different modified insulating oils (mineral oil and synthetic ester oil) with different types of nanoparticles at different concentrations (0.0, 0.0025, 0.005, and 0.01 wt%). From the obtained results, it is noticed that the thermal stress on the MOCB can be reduced by the use of high thermal conductivity insulating oils. Nano/insulating oils decrease internal temperature and generate heat energy inside the MOCB by about 17.5%. The corresponding physical mechanisms are clarified considering the thermophoresis effect.