All over the world, increasing anthropogenic activities, industrialization, and urbanization have intensified the emissions of various pollutants that cause air pollution. Marble quarries in Pakistan are abundant and there is a plethora of small- and large-scale industries, including mining and marble-based industries. The air pollution caused by the dust generated in the process of crushing and extracting marble can cause serious problems to the general physiological functions of plants and it affects human life as well. Therefore, the objectives of this study were to assess the air quality of areas with marble factories and areas without marble factories, where the concentration of particulate matter in terms of total suspended particles (TSP) was determined. For this purpose, EPAM-5000 equipment was used to measure the particulate levels. Besides this, a spectrophotometer was used to analyze the presence of PM2.5 and PM10 in the chemical composition of marble dust. It was observed that the TSP concentrations in Darmangi and Malagori areas of Peshawar, Pakistan—having marble factories—were 626 µg/m3 and 5321 µg/m3 respectively. The (PM2.5, PM10) concentration in Darmangi was (189 µg/m3, 520 µg/m3) and in Malagori, it was recorded as (195 µg/m3, 631 µg/m3), which was significantly higher than the non-marble dust areas and also exceeded WHO recommended standards. It was concluded that the areas with the marble factories were more susceptible to air pollution as the concentration of TSP was significantly higher than the recommended TSP levels. It is recommended that marble factories should be shifted away from residential areas along with strict enforcement. People should be instructed to use protective equipment and waste management should be ensured along with control mechanisms to monitor particulate levels.
Concrete is one of the most commonly used construction materials; however, its durability plays a pivotal role in areas where the concrete is exposed to severe environmental conditions, which initiate cracks inside and disintegrate it. Randomly distributed short fibers arrest the initiation and propagation of micro-cracks in the concrete and maintain its integrity. Traditional polypropylene fibers are thin and encounter the problem of balling effects during concrete mixing, leading to uneven fiber distribution. Thus, a new polypropylene fiber is developed by gluing thin ones together, forming macro-polypropylene fibers. Thus, different amounts of fibers, 0–1.5% v/f with an increment of 0.5% v/f, are used in different grades of concrete to study their impact on durability properties, including resistance to freezing and thawing cycles, sulfate, and acid attacks. A total of 432 cube samples were tested at 28, 56, and 92 days. The results reveal that the maximum durability, in terms of compressive strength loss, is noted with a fiber content of 1% with improved resistance of 72%, 54%, and 24% against freeze–thaw cycles, sulfate attack, and hydrochloric acid attack, respectively, at 92 days. Thus, the resulting fiber-reinforced concrete may be effective in areas where these extreme exposure conditions are expected.
13 January 2020 in Iranian Journal of Science and Technology, Transactions of Civil Engineering
The obstruction offered by the surrounding concrete to the pulling out of embedded steel bar is known as bond strength. Steel fibers addition to concrete improves its bond strength by arresting the cracks due to their bridging effect. Bond failure occurs when cracks in the surrounding concrete initiates, providing enough space for bar to be pulled-out. Micro steel fibers efficiently control the formation of micro cracks and may improve bond strength to a greater extent compared to the longer steel fibers. However, it reduces the workability of concrete which is of greater importance in case of self-compacting concrete (SCC). Reduction of workability is less pronounced when straight micro steel fibers are used due to their shorter lengths and straight geometry. Thus, different amount of straight micro steel fibers (0.25 %, 0.5 %, 0.75 %) were incorporated in to SCC to investigate their fresh and mechanical properties with major emphasis on the bond strength. Results indicate that steel fibers addition to SCC improve the splitting tensile strength and bond strength significantly with a maximum increase of 33.5 % and 54.9 % respectively with 0.75 % fibers addition. An equation is proposed for the calculation of bond strength with micro steel fibers addition to SCC with a maximum variation of 4 % to those of experimental values.
20 May 2020 in International journal of Engineering Works