This paper describes a practical method for obtaining the spectra of lights emitted by a fluor in a liquid scintillator (LS) using a digital camera. The emission wavelength results obtained using a digital image were compared with those obtained using a fluorescence spectrophotometer. For general users, conventional spectrophotometers are expensive and difficult to access. Moreover, their experimental measurement setup and processes are highly complicated, and they require considerable care in handling. To overcome these limitations, a feasibility study was performed to obtain the emission spectrum through image analysis. Specifically, the emission spectrum of a fluor dissolved in a liquid scintillator was obtained using digital image analysis. An image processing method was employed to convert the light irradiated during camera exposure into wavelengths. Hue (H) and wavelength (W) are closely related. Thus, we obtained an H-W response curve in the 400~450 nm wavelength region, using a light-emitting diode. Another relevant advantage of the method described in this study is its non-invasiveness in sealed LS samples. Our results showed that this method has the potential to accurately investigate the emission wavelengths of fluor within acceptable uncertainties. We envision the use of this method to perform experiments in chemistry and physics laboratories in the future.
This manuscript describes an innovative method to tag muons using the baseline information of the Flash ADC (FADC) waveform of PMTs in the JSNS2 (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment. The experiment is designed to search for evidence of sterile neutrinos, and a reliable method for muon tagging is an essential component for background rejection because the detector is located above ground, on the 3rd floor of the J-PARC Material and Life Science Experimental Facility (MLF). Cosmogenic muons that stop within the detector volume and produce a Michel electron are a particularly important background that must be rejected for our sterile neutrino search. Utilizing this innovative method, more than 99.8 % of Michel electrons can be rejected even without using information from the detector's veto region PMTs. This technique can be employed by any experiments which uses a similar detector configuration.
8 July 2020 in IEEE Transactions on Nuclear Science
The properties of neutrinos are not well known because they weakly interact with surrounding matter. Recently, several interesting results and phenomena have been measured using reactor neutrinos. Although there are various types of detectors that detect neutrino signals, they generally use photomultiplier tubes (PMTs) to collect data. In particular, signals obtained from each PMT surrounding a detector are used to reconstruct a vertex of an incident neutrino in the detector. However, if a number of PMTs are out of operation from the initial installation, the performance of the PMT or its operation efficiency may be changed over time. This may affect the information for the reconstructed vertex of an incident neutrino, which can have a direct impact on results that utilize the reconstructed vertex information. This article briefly describes the change of reconstructed vertex according to operating status of PMTs around the reactor neutrino detector by using a Monte Carlo (MC) simulation based on a cylindrical detector equipped with liquid scintillator. The MC simulation for this analysis needs a moderate number of central processing units (CPUs) and cores. Therefore, various resources and servers at a supercomputing center were used. Our results can be used to more accurately conduct research related to neutrino direction using PMT information in the future.
27 January 2020 in Journal of the Korean Physical Society
This paper describes in detail the uncertainties due to several factors that may affect the direction vector of a reactor neutrino in a liquid scintillatio
19 September 2017 in Journal of Physics: Conference Series
RENO has been taking data since August, 2011 and successfully measured the smallest neutrino mixing angle, theta13. This measurement was based on observed reactor neutrino events with neutron captures on gadolinium (n-Gd) in the target detector region. RENO also successfully measures the mixing angle from a reactor neutrino sample with neutron captures on hydrogen (n-H) in the gamma-catcher region. Due to a large accidental background in the n-H data sample, the analysis requires additional reduction of backgrounds. This independent measurement provides a valuable systematic cross-check of the θ13 measurement using the n-Gd sample. In this paper, we present the results from the n-H analysis using the 500 days of data sample.
The JSNS2-II (the second phase of JSNS2, J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment aimed at searching for sterile neutrinos. This experiment has entered its second phase, employing two liquid scintillator detectors located at near and far positions from the neutrino source. Recently, the far detector of the experiment has been completed and is currently in the calibration phase. This paper presents a detailed description of the calibration process utilizing the LED system. The LED system of the far detector uses two Ultra-Violet (UV) LEDs, which are effective in calibrating all of PMTs at once. The UV light is converted into the visible light wavelengths inside liquid scintillator via the wavelength shifters, providing pseudo-isotropic light. The properties of all functioning Photo-Multiplier-Tubes (PMTs) to detect the neutrino events in the far detector, such as gain, its dependence of supplied High Voltage (HV), and Peak-to-Valley (PV) were calibrated. To achieve a good energy resolution for physics events, up to 10% of the relative gain adjustment is required for all functioning PMTs. This will be achieved using the measured HV curves and the LED calibration. The Peak-to-Valley (PV) ratio values are the similar to those from the production company, which distinguish the single photo-electron signal from the pedestal. Additionally, the precision of PMT signal timing is measured to be 2.1 ns, meeting the event reconstruction requirement of 10 ns.