The opaque photovoltaic thermal (PVT) produces both thermal and electrical energy. In order to increase thermal energy, we have considered flexible (Al based) PV module for the present study. Further, we have considered thermo-electric cooler (TEC) integrated with flexible PV module to enhanced electrical power. Hence, an overall power can be increases in flexible PVT-TEC collector. A concept of series and parallel combination of flexible PVT-TEC collectors is proposed to optimize of series (n) and parallel (m) combinations for a given number of N (= n × m) collectors for maximum overall exergy depending on thermal and electrical energy which has not been considered yet so far. Further, a new expression has also been developed for the heat removal factor and instantaneous thermal efficiency of nth flexible PVT-TEC collector to investigate its effect on the nth flexible PVT-TEC collector performance. Numerical computations have been carried out for a given coldest climatic condition of Srinagar, India and design parameters of Al-based PVT-TEC collectors using MATLAB R2021b. Based on numerical computations, following conclusions have been drawn:
17 September 2024 in Journal of Cleaner Production
In order to increase biogas production during winter months/cold climatic conditions, a self-sustained N-photovoltaic thermal and flat plate collector (PVT-FPC) hybrid active heating biogas plant has been analyzed in terms of thermal energy and electrical energy. A general analytical expression for thermal and electrical energy of the biogas plant has been derived as a function of climatic and design parameters from one order coupled differential equations. Various photovoltaic thermal and flat plate collector (N-PVT-FPC) configurations have been considered for optimizing maximum electrical and thermal energy gain for a given total number of N-PVT-FPC collectors. Based on mathematical computation for Indian cold climatic conditions, it has been found that the N-PVT-FPC combination is always better than the flat plate collector-photovoltaic thermal (N-FPC-PVT) collector for maximum electrical and thermal energy. Overall exergy analysis of hybrid active heating of biogas plants has also been carried out.
Electrolyzer technology necessitates the use of seawater instead of freshwater to achieve a comprehensive supply of clean and economical energy. However, the tendency of chloride ions (Cl−) to significantly erode the metal surface is a major challenge during seawater electrolysis. Therefore, designing an electrode that is resistant to chloride ions is of great importance to develop an efficient seawater electrolyser. In this work, we present a double layer anode consisting of a molybdenum sulfide electrocatalyst uniformly deposited over sulfonated graphene sheets coated over an Ni foam. The developed electrode (GNiMoOS) helps selectively convert H2O into H2 and O2 rather than chloride (Cl−) ions into ClO− in a seawater environment by resisting corrosion due to the Cl− ions in seawater. The chromogenic substrate 3,3′,5,5′-tetramethylbenzidine (TMB) provides solid evidence that the GNiMoOS electrocatalyst blocks the chloride oxidation reaction owing to its distinct resistance to Cl−. In addition, density functional theory (DFT) calculations clearly validated the preference of sulfonic moieties towards OH− compared with Cl− ions, confirming the chlorine repelling properties of the GNiMoOS electrode. The successful in situ functionalisation of sulfonic moieties into the reduced graphene oxide (RGO) skeleton with simultaneous development of flower-like MoS2 was well confirmed using XPS, Raman, SEM, TEM, and FT-IR techniques. GNiMoOS delivered an impressive current density of 100 mA cm−2 for OER and HER at room temperature, requiring remarkably low overpotentials of just 180 mV and 201 mV, respectively. Industrial faradaic current densities (400–600 mA cm−2) were reported with the active electrode at combined overpotentials of ≤600 mV at room temperature. The unique morphology of MoS2 provides more active sites for the HER/OER, while sulfonated functional groups over graphene impart much-needed anticorrosion properties to the system. Moreover, the electrical coupling between MoS2 and RGO can make the electron transfer to RGO easier. Therefore, the synergistic interactions among MoS2, SO3H and RGO lead to improved catalytic activity and prolonged stability.
Nanocatalysts for sustainable water electrolysis is strongly desirable to promote the commercialization of H2 as the alternate clean energy source for the future. The goal is cheaper hydrogen production from sea and low grade water by minimizing the energy consumption and using low cost cell components & non-noble metal catalysts. The conductivity of metal nitrides and their ability to carry out Hydrogen Evolution Reaction and Oxygen Evolution Reaction at relatively low overpotential render these one of the frontline candidates to be potentially utilized as the catalyst for low cost H2 production via electrolysis. In this chapter, the potential of metal nitride catalyst towards fulfilling the above objective is discussed. The synthesis of various metal nitride catalysts, their efficiency towards electrode half reactions and the effectiveness of these class of nanocatalyst for electrolysis of sea water is elaborated. A review of recent literature with special reference to the catalyst systems based on non-noble metals will be provided to assess the likelihood of these nanocatalyst to serve as a commercial grade electrode material for sea water electrolysis.