Membrane gas separation is a prospective technology for hydrogen separation from various refinery and petrochemical process streams. To improve efficiency of gas separation, a novel hybrid membrane consisting of nanodiamonds and P84 copolyimide is developed. The particularities of the hybrid membrane structure, physicochemical, and gas transport properties were studied by comparison with that of pure P84 membrane. The gas permeability of H2, CO2, and CH4 through the hybrid membrane is lower than through the unmodified membrane, whereas ideal selectivity in separation of H2/CO2, H2/CH4, and CO2/CH4 gas pairs is higher for the hybrid membrane. Correlation analysis of diffusion and solubility coefficients confirms the reliability of the gas permeability results. The position of P84/ND membrane is among the most selective membranes on the Robeson diagram for H2/CH4 gas pair.
Hybrid membranes based on poly (2,6-dimethyl-1,4-phenylene oxide) modified with heteroarm stars (HAS) were developed to separate ethylene glycol/water mixtures by pervaporation. The HAS consist of a small branching center fullerene C 60 and twelve arms of different nature, six arms of nonpolar polystyrene and six arms of polar poly-tert-butyl methacrylate. The changes of structure and physical properties with HAS inclusion were systematically studied using SEM, X-ray diffraction analysis, TGA, and contact angle measurements. Mass transfer of ethylene glycol and water through membranes was studied by sorption and pervaporation tests. It was found that the growth of HAS content up to 5 wt% in the membrane leads to an increase in the total flux and a strong increase in the separation factor. To evaluate intrinsic properties of the penetrant–membrane system, permeability and selectivity were calculated. Overall, utilizing star-shaped macromolecules as a filler can be a promising way to improve the separation performance of diffusion membranes.
Modern ultrafiltration requires novel perfect membranes with narrow pore size, high porosity, and minimal pore tortuosity to achieve high separation performance. In this work, copolyamic acid (co-PAA) was synthesized and used for the preparation of asymmetric porous membranes by phase inversion technique. Several co-PAA membranes were heated up to 250 °C; during heating, they undergo solid-phase transformation into co-polybenzoxazinoneimide (co-PBOI) via dehydration and cyclization. Comparative characterization of both co-PAA and co-PBOI membranes was realized by scanning electron microscopy, mechanical testing, thermogravimetric analysis, and ultrafiltration experiments. Membrane calibration was carried out using a mixture of seven proteins with different molecular weights. During heat treatment, the molecular weight cut-off of the membranes decreased from 20 × 103 g/mol (co-PAA) to 3 × 103 g/mol (co-PBOI). Abnormally low dispersions of rejection (0.3 for co-PAA and 0.45 for co-PBOI) were observed for the studied membranes; this fact indicates that the membranes possess enhanced resolving power.
The use of perovskite-type layered oxide K2La2Ti3O10 (Per) as a modifier of the Torlon® polyamide-imide (PAI) membrane has led to the formation of an specific structure of a dense nonsymmetrical film, namely, a thin perovskite-enriched layer (3–5 μm) combined with the polymer matrix (~30 μm). The PAI/Per membrane structure was studied by SEM in combination with energy dispersive microanalysis of the elemental composition which illustrated different compositions of top and bottom surfaces of the perovskite-containing membranes. Measurement of water and alcohol contact angles and calculation of surface tension revealed hydrophilization of the membrane surface enriched with perovskite. The transport properties of the nonsymmetrical PAI/Per membranes were studied in the pervaporation of ethanol‒ethyl acetate mixture. The inclusion of 2 wt.% Per in the PAI gives a membrane with a high separation factor and increased total flux.
26 December 2022 in Membranes and Membrane Technologies
Composites containing up to 5 wt % montmorillonite (MMT) nanoparticles are created based on natural materials, cellulose acetate and MMT, and film membranes are prepared. The characteristic features of the membrane morphology are studied by scanning electron microscopy. The transport properties of the membranes are studied for the process of separation of a methanol–methyl tert-butyl ether (MTBE) mixture. The degree of equilibrium sorption and diffusion coefficients of methanol and MTBE in the membranes are determined. The pervaporation of a methanol–MTBE mixture is studied in a wide range of feed compositions including the azeotropic point. The best separation factor combined with a high flux is found for a membrane containing 3% MMT. The study of the deformation behavior of the membranes under uniaxial tension shows that they have good mechanical properties, and the elastic modulus increases with the increase in the MMT content while the strength slightly decreases.
Novel polymer composite materials, including unique nanoparticles, contribute to the progress of modern technologies. In this work, the endohedral fullerene C60 with incapsulated iron atom (endometallofullerene Fe@C60) is used for modification of P84 copolyimide. The impact of 0.1, 0.5, and 1 wt % endometallofullerene on the structure and physicochemical properties of polymer films is studied through scanning electron microscopy, thermogravimetric analysis, and thermomechanical tests. Transport properties are estimated through sorption and pervaporation techniques toward methanol and methyl acetate mixture. The inclusion of endometallofullerene into the copolyimide matrix improves membrane permeability and selectivity in the separation of methanol—methyl acetate mixtures. The maximal effect is achieved with a composite containing 0.5 wt % Fe@C60. The developed composites are effective for energy and resource saving purification of methyl acetate by pervaporation.