Its unexcelled mechanical and physical properties, in addition to its biocompatibility, have made stainless steel 304 a prime candidate for a wide range of applications. Among different manufacturing techniques, electrical discharge machining (EDM) has shown high potential in processing stainless steel 304 in a controllable manner. This paper reports the results of an experimental investigation into the effect of the process parameters on the obtainable surface roughness and material removal rate of stainless steel 304, when slotted using wire EDM. A full factorial design of the experiment was followed when conducting experimental trials in which the effects of the different levels of the five process parameters; applied voltage, traverse feed, pulse-on time, pulse-off time, and current intensity were investigated. The geometry of the cut slots was characterized using the MATLAB image processing toolbox to detect the edge and precise width of the cut slot along its entire length to determine the material removal rate. In addition, the surface roughness of the side walls of the slots were characterized, and the roughness average was evaluated for the range of the process parameters being examined. The effect of the five process parameters on both responses were studied, and the results revealed that the material removal rate is significantly influenced by feed (p-value = 9.72 × 10−29), followed by current tension (p-value = 6.02 × 10−7), and voltage (p-value = 3.77 × 10−5), while the most significant parameters affecting the surface roughness are current tension (p-value = 1.89 × 10−7), followed by pulse-on time (1.602 × 10−5), and pulse-off time (0.0204). The developed regression models and associated prediction plots offer a reliable tool to predict the effect of the process parameters, and thus enable the optimizing of their effects on both responses; surface roughness and material removal rate. The results also reveal the trade-off between the effect of significant process parameters on the material removal rate and surface roughness. This points out the need for a robust multi-objective optimization technique to identify the process window for obtaining high quality surfaces while keeping the material removal rate as high as possible.
Competitive globalization and automated process management through a functional information platform that supports technologies such as enterprise resource planning (ERP) are critical to improving the performance of any business. Research studies show that a large number of (ERP) projects fail during implementation. Other studies have shown that the effectiveness of ERP implementation in improving production processes is modest or low, even for well-designed systems. This study takes an in-depth look at the critical success factors of ERP implementation that impact business success, and conducts a case study to analyze the results obtained and assess their impact on performance.
Composite materials, such as aluminum alloy FGMs, provide advantageous weight reduction properties compared to homogenous pure structures while still preserving sufficient stiffness for diverse applications. Despite various research on drilling simulation concepts and ideas for these materials, there still needs to be an agreement on the process modeling. Researchers have looked into a lot of different numerical methods, including Lagrangian, Eulerian, arbitrary Lagrangian–Eulerian (ALE), and coupled Eulerian–Lagrangian (CEL), to find solutions to problems like divergence issues and too much mesh distribution, which become more of a problem at higher speeds. This research provides a global analysis of bottom-up meshing for eleven 1 mm layers using ABAQUS® software. It combines the internal surface contact approach with the Lagrangian domain’s kinematic framework. The model uses the Johnson–Cook constitutive equation to precisely predict cutting forces, stress, and strain distributions, optimizing cutting parameters to improve drilling performance. According to Taguchi analysis, the most favorable parameters for reducing cutting force and improving performance are a rotational speed of 700 rpm, a feed rate of 1 mm/s, and a depth of cut of 3 mm. The findings suggest that increasing the feed rate and depth of cut substantially affects the cutting force, while the rotational speed has a comparatively little effect. These ideal settings serve as a foundation for improving FGM drilling efficiency.
This research investigates the multi-response of both material removal rate (MRR) and surface roughness (Ra) for the wire electrical discharge machining (WEDM) of two stainless steel alloys: AISI 304 and AISI 316. Experimental results are utilized to compare the machining responses obtained for AISI 316 with those obtained for AISI 304, as previously reported in the literature. The experimental work is conducted through a full factorial experimental design of five running parameters with different levels: applied voltage, transverse feed, pulse-on/pulse-off times and current intensity. The machined workpieces are analyzed using an image processing technique in order to evaluate the size of cut slots to allow the calculation of the MRR. Followed by the characterization of the surface roughness along the side walls of the slots. Different mathematical regression techniques were developed to represent the multi-response of both materials using the MATLAB regression toolbox. It was found that WEDM process parameters have a fuzzy influence on the responses of both material models. This allowed for multi-objective optimization of the regression models using four different techniques: multi-objective genetic algorithm (MOGA), multi-objective pareto search algorithm (MOPSA), weighted value grey wolf optimizer (WVGWO) and osprey optimization algorithm (OOA). The optimization results reveal that the optimal WEDM parameters of each response are inconsistent to the others. Hence, the optimal results are considered a compromise between the best results of different responses. Noteworthily, the multi-objective pareto search algorithm outperformed the other candidates. Eventually, the optimal results of both materials share the high voltage, high transverse feed rate and low pulse-off time parameters; however, AISI 304 requires low pulse-on time and current intensity levels while AISI 316 optimal results entail higher pulse-on time and current levels.
The measurement uncertainty has a significant impact on quality control processes. This is particularly true of standards that are assessed to determine if a product is compliant. This ambiguity introduces two potential risks of decision-making: accepting a non-conventional product (the consumer's risk) or rejecting a conventional product (the producer's risk). This investigation explores the potential for false decisions caused by measurement errors in product assessments. By studying data near the control limits, a greater understanding of the manufacturing process is intended to facilitate informed decision-making, and guide the implementation of effective quality control methods. The investigation highlights the importance of selecting suitable measurement instruments to reduce false positive quality control decisions, which resulted in 11.43% of initially accurate parts violating the 0.1 mm tool. The 0.001 mm tool has a higher degree of precision than the 0.01 mm tool, but it may not always be practical financially