Subgrade soil characterization, in terms of resilient modulus, is crucial for both flexible and rigid pavement design. Resilient moduli measured through repeated triaxial load tests on cylindrical disturbed/undisturbed samples are frequently used for characterizing subgrade soil. Because of the complexities encountered with the test, in-situ and other laboratory tests would be desirable if a reliable correlation can be established. In this paper, data from two-field test programs was used in developing correlation equations to predict resilient modulus of fine- and coarse-grained soils. Undisturbed samples are extracted from 12 in-service Mississippi subgrades, using a Shelby tube, and tested in a repeated triaxial machine for MR employing AASHTO TP46-94 protocol. The results suggest two comprehensive models—one for fine-grained and another for coarse-grained soil—in correlating laboratory MR to stress state. Model parameters are then correlated with soil index properties allowing the models to capture the effect of stress state, soil type and soil properties. For model verification, an independent set of data from nine different Mississippi subgrades is used, observing good comparison between actual and predicted moduli.
1 September 2005 in International Journal of Pavement Engineering
Mechanistic pavement design procedures based on elastic layer theory require characterization of each material in the pavement structure in terms of elastic moduli. Repeated triaxial load tests on cylindrical disturbed/undisturbed samples, yielding a resilient modulus, are frequently used for characterizing subgrade soil. Because of the complexities encountered with the test, in-situ and other laboratory tests would be desirable if a reliable correlation can be established. Relying on data from two-field test programs, correlation equations to predict MR for fine- and coarse-grained (sandy) soils are proposed in this paper. Twelve test sections reflecting a range of typical subgrade soil materials of Mississippi are selected and tested. Undisturbed samples are extracted and tested in a repeated triaxial machine for MR, employing AASHTO TP46-94 protocol. Other soil index properties are also determined, facilitating soil classification according to AASHTO procedure. The results suggest two relations—one for fine-grain and another for coarse-grained (sandy) soil—in correlating laboratory MR to soil index properties. These models include the most relevant factors that influence MR values. For model verification, an independent set of data is used, observing good comparison between actual and predicted moduli. These models with the soil properties included could be used in levels 2 and 3 in the new 2002 AASHTO Design Guide substituting other empirical correlations (level 2) and the use of modulus typical values (level 3).
13 May 2009 in International Journal of Pavement Engineering
Crack, seat and overlay (CS&O) is a rehabilitation technique that has been used on jointed plain concrete pavements. Only a few studies have evaluated the surface roughness of pavement sections rehabilitated using this technique. The purpose of this paper was to evaluate the roughness of roadway sections rehabilitated employing the CS&O technique. The data extracted from the long-term pavement performance database were separated based on the weather region and analysed. Then, international roughness index (IRI) prediction models were developed. A separate model was developed for pavement sections in California. For sections with bound bases, thick overlays provide a smoother surface (lower IRI). However, the effect of the overlay thickness on the IRI for sections with unbound bases does not appear to be considerable. Prediction models developed in this study are shown to provide adequate predictive capabilities. Sections in California have initial IRI values that are lower than those found for sections in the wet-with-freeze (WF) and wet-with-no-freeze (WNF) regions. However, California sections are predicted to develop higher IRI values over time, when compared to those sections in the WF and WNF regions.
1 January 2013 in Transportation Research Record: Journal of the Transportation Research Board
Crack, seat, and overlay (CS&O) is a rehabilitation technique used on jointed plain concrete pavements in California. Although CS&O is widely used, few studies have attempted to develop performance prediction models for pavements that have been rehabilitated with this technique. This study evaluated CS&O performance for surface roughness and transverse reflection cracking. Performance data for CS&O sections in three geographic regions in California were used to develop regression performance models. These models can be incorporated into the California Department of Transportation pavement management system and used to predict future performance, assist with life-cycle cost analyses, and optimize the allocation of resources. The results of a sensitivity analysis suggest that section age is the most significant factor affecting the deterioration of CS&O pavements. Secondary factors include the annual equivalent single-axle load and layer thickness ratio. Section age as an independent variable would include the impact of environmental loading cycles. Other factors related to subgrade conditions, temperature variations, and construction variability could not be investigated because data were not available. However, their impact is inherent to the models.
17 May 2024 in American Journal of Civil Engineering
Previous research indicated that nanomaterials have potential in improving pavement properties, particularly moisture resistance. This study evaluated the effectiveness of nanoclays in enhancing the resistance of Hot Mix Asphalt (HMA) to moisture damage and compared its performance to standard modifiers. Asphalt binder modified using four additives was tested using a Dynamic Shear Rheometer (DSR) before and after being aged in a Rolling Thin Film Oven (RTFO): two surface-modified nanoclays and two liquid anti-stripping chemicals (HP+ and LOF 6500). The DSR and RTFO tests showed that the two nanoclays had a stiffening effect on the binder, while both liquid antistripping agents had the opposite effect, decreasing both the elastic and complex modulus of the binder. After RTFO aging, similar trends were observed, except the binder had become much stiffer in all cases. HMA designed employing the Superpave mix design procedure was tested for moisture sensitivity in accordance with AASHTO T-283. The dry tensile strength for the two nanoclays and LOF 6500 modified mixes were higher than the control mix. However, all modified mixes resulted in wet tensile strengths that were higher than the control. The tensile strength ratios for all modified mixes were also higher than the control and exceeded the Superpave mix design method minimum of 0.80. Evaluation of these additives in the field would further benefit asphalt pavement research.
High reclaimed asphalt pavement (RAP) mixtures can improve pavement sustainability by reducing virgin binder and aggregate demand, but high RAP contents may increase mixture stiffness and reduce cracking tolerance. This study evaluates whether commercially available para-aramid fibers can improve the intermediate-temperature cracking resistance of high-RAP hot-mix asphalt using the IDEAL-CT test. Two para-aramid fiber products, a wax-coated fiber and an emulsion-treated fiber, were evaluated at dosages of 0.05%, 0.10%, and 0.15% by total mixture weight in asphalt mixtures containing 15%, 25%, and 40% RAP. The results showed that fiber effectiveness depended strongly on RAP content, fiber treatment, and dosage. The 25% RAP mixture had the lowest control CTIndex and showed the greatest improvement from fiber addition. In this group, 0.10% wax-coated fiber increased CTIndex by 170%, while 0.15% emulsion-treated fiber increased CTIndex by 263%. For the 15% RAP mixture, 0.05% emulsion-treated fiber and 0.10% wax-coated fiber produced statistically significant improvements. For the 40% RAP mixture, 0.10% emulsion-treated fiber produced the highest mean CTIndex among all mixtures tested, but the improvement was not statistically significant because of high specimen variability. Overall, the findings indicate that para-aramid fibers can improve laboratory cracking resistance in RAP mixtures, but the optimum dosage is mixture-specific and should not be applied uniformly across RAP contents. Because this study was limited to Ideal-CT, additional rutting, fatigue, aging, workability analysis and field validation are recommended before broad implementation.