The coatings used in cans can release complex chemical mixtures into foodstuffs. Therefore, it is important to develop analytical methods for the identification of these potential migrant compounds in packaged food to guarantee the compliance with European food packaging legislation and ensure consumer safety. In the present work, the type of coating in a total of twelve cans collected in Santiago de Compostela (Spain) were evaluated using an ATR (attenuated total reflectance)-FTIR spectrometer. These samples were analysed after extraction with acetonitrile in order to identify potential migrants through a screening method by gas chromatography coupled to mass spectrometry (GC-MS). A total of forty-seven volatile and semi-volatile compounds were identified in these samples, including plasticizers, photoinitiators, antioxidants, lubricants, etc. Then, in a second step, a targeted analysis was carried out for the simultaneous determination of 13 compounds, including bisphenols (BPA, BPB, BPC, BPE, BPF, BPG) and BADGEs (BADGE, BADGE.H₂O, BADGE.2H₂O, BADGE.HCl, BADGE.2HCl, BADGE.H₂O.HCl, cyclo-di-BADGE) by liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) with atmospheric pressure chemical ionisation (APCI) source. Among all the bisphenols analysed, only the bisphenol A was detected in four samples; while cyclo-di-BADGE was the predominant compound detected in all the samples analysed.

Major type of internal can coating used for food and beverages is made from epoxy resins, which contain among their components bisphenol A (BPA) or bisphenol A diglycidyl ether (BADGE). These components can be released and contaminate the food or beverage. There is no specific European legislation for coatings, but there is legislation on specific substances setting migration limits. Many investigations have paid attention to BPA due to its classification as endocrine disruptor, however, few studies are available concerning to other bisphenol analogues that have been used in the manufacture of these resins. To evaluate the presence of this family of compounds, ten cans of beverages were taken as study samples. Firstly, the type of coating was verified using an attenuated total reflectance-FTIR spectrometer to check the type of coating presents in most of the samples examined. A screening method was also performed to investigate potential volatiles from polymeric can coatings of beverages using Purge and Trap (P&T) technique coupled to gas chromatography with mass spectrometry detection (GC-MS). Moreover, a selective analytical method based on high performance liquid chromatography with fluorescence detection (HPLC-FLD) for the simultaneous identification and quantification of thirteen compounds including bisphenol analogues (BPA, BPB, BPC, BPE, BPF, BPG) and BADGEs (BADGE, BADGE.H2O, BADGE.2H2O, BADGE.HCl, BADGE.2HCl, BADGE.H2O.HCl, cyclo-di-BADGE) in the polymeric can coatings and in the beverage samples was applied. In addition, a liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) method was optimized for confirmation purposes. The method showed an adequate linearity (R2 >0.9994) and low detection levels down to 5 µg/L. Cyclo-di-BADGE was detected in all extracts of polymeric coatings. The concentrations ranged from 0.004 to 0.60 mg/dm2. No detectable amounts of bisphenol related compounds were found in any of the beverage samples at levels that may pose a risk to human health, suggesting a low intake of bisphenols from beverages.

Polymeric coating formulations may contain different components such as cross-linking agents, resins, lubricants, and solvents, among others. If the reaction process or curing conditions are not applied in a proper way, these components may remain unreacted in the polymeric network and could be released and migrate into foods. In this study, several polyester coatings intended for food contact were investigated. Firstly, Fourier-transform infrared spectroscopy with an attenuated total reflectance (ATR-FTIR) spectrometer and confocal Raman microscopy were used to identify the type of coating. Then, different techniques, including gas chromatography coupled to mass spectrometry (GC-MS) and analysis by matrix-assisted laser desorption coupled to time-of-flight mass spectrometry (MALDI-TOF-MS), among others, were used to investigate the potential volatile and non-volatile migrants. Moreover, migration assays were carried out to evaluate the presence of monomers and to tentatively identify possible oligomers below 1000 Da. The analyses were performed by liquid chromatography coupled to ion trap mass spectrometry (LC-MSⁿ). Using the information collected from each analytical technique, it was possible to elucidate some of the starting substances used in the formulation of the polyester coatings analyzed in this study. In migration tests, several polyester oligomers were tentatively identified for which there is not toxicological data available and, therefore, no migration limits established to date.