Phase-change materials (PCMs) are becoming more widely acknowledged as essential elements in thermal energy storage, greatly aiding the pursuit of lower building energy consumption and the achievement of net-zero energy goals. PCMs are frequently constrained by their subpar heat conductivity, despite their expanding importance. This in-depth research includes a thorough categorization and close examination of PCM features. The most current developments in nanoencapsulated PCM (NEPCMs) techniques are also highlighted, along with recent developments in thermal energy storage technology. The assessment also emphasizes how diligently researchers have worked to advance the subject of PCMs, including the creation of devices with improved thermal performance using nano-enhanced PCMs (NEnPCMs). This review intends to highlight the progress made in improving the efficiency and efficacy of PCMs by providing a critical overview of these improvements. The paper concludes by discussing current challenges and proposing future directions for the continued advancement of PCMs and their diverse applications.
26 April 2022 in Journal of Solar Energy Engineering
The high cost of the solar tracking systems is the major obstacle facing the growth of the solar harvesting technology. Therefore, reducing the solar tracking cost is necessary for developing this important energy sector. This study developed a simple and low-cost solar tracking system for parabolic concentrator (PCST) assisting tubular solar still (TSS). A single-axis solar tracking mechanism is developed based on two small light-dependent resistors (LDRs) shielded by a blank sheet which keeps the two cells shielded from sunlight. When the sunlight moves, one of the two LDRs will gain some light activating a switch to turn on the driving motor moving the system in the opposite direction till the LDR shielded again. By this simple mechanism, the two LDRs are shielded from sunlight all the time and consequently, the solar collector is always facing the sunlight. A simple parametric study is also conducted for an efficient PCST-TSS device with higher freshwater productivity. The performance of the most promising five design categories is compared. Results showed that the lowest cost tracking system was 34.6% lower than the highest one. Moreover, the lowest CPL was $0.0074/L which is 43.1% lower than the highest CPL category. Moreover, a comparison with other studies showed high potential for the present significant reduction in the cost which ranges between 43.1% and 87% compared with the recent related studies. The developed device is fully self-reliance and suitable for rural and isolated communities having limited infrastructure.
26 September 2022 in Journal of Solar Energy Engineering
The behavior of a retired lithium-ion battery (LIB) from its first-life in an electric aircraft (EA) to its second-life in a solar photovoltaic (PV) system for a net-zero electricity residential home is studied. The first part of this study presents the design and sizing of a battery energy storage system (BESS), made from retired LIBs, to store a portion of the PV generation for a typical home in Ohio. The home is connected to the grid, but the net electricity usage from the grid in one year is zero. The purpose of the BESS is to peak shaving, power arbitrage, reduce the home dependency on the grid, and increase the economic benefits. The sizing is determined based on the hourly data of the PV system generation, ambient temperature, irradiation, and home demand electricity. In the second part of this study, the retired LIB degradation rate and its remaining useful life in the BESS are estimated using an adopted empirical LIB model. The model includes the capacity-fade for both first-life and second-life of the LIB under various duty cycles. It is shown that the retired LIB from its first-life is still suitable to be used in the PV grid-tied battery (PVGB) system for another 10 years. The results of this study can potentially reduce the LIB cost for electric vehicles (EVs) and EAs because the retired LIBs from these applications still have value to serve for other applications such as PVGB systems for residential homes.
The use of 3D printing is expanding in manufacturing wind turbine blades for renewable energy. This study examines the relationship between geometric parameters, mechanical strength, and aerodynamic performance in blades made from short carbon fiber-reinforced PLA (SCFR-PLA) composites. To achieve this, it includes a comparative evaluation of innovative blade designs and materials, aiming to enhance both the energy efficiency and mechanical durability of horizontal axis wind turbines (HAWTs). The numerical model of the wind turbine blade is validated against experimental results, which employed a NACA geometry and ABS polymer. Building upon this validation, a design of experiments (DOE) analysis is employed to explore the influence of fused filament fabrication (FFF) parameters on the mechanical properties of SCFR-PLA composites. A novel blade design, referred to as HAWTSav, is numerically evaluated using 3D-printed SCFR-PLA composites. Numerical simulations are conducted to evaluate the energy efficiency and structural integrity of the HAWTSav blade. A comparative analysis is then performed, contrasting the performance of the conventional NACA blade in ABS with the HAWTSav blade in SCFR-PLA composites. The findings highlight the potential of SCFR-PLA composites in the development of efficient and durable wind turbine blades, highlighting their applicability, particularly in small-scale wind energy systems.
The present study deals with electrically conductive fluid flow across a heated circular cylinder to examine the oscillatory magnetic flux and heat transfer in the presence of variable surface temperature. The proposed mathematical formulation is time-dependent, which is the source of the amplitude and fluctuation in this analysis. The designed fluctuating nonlinear computational model is associated with the differential equations under specific boundary conditions. The governing equations are converted into dimensionless form by using adequate dimensionless variables. To simplify the resolution of the set of governing equations, it is further reduced. The effects of surface temperature parameter , magnetic force number , buoyancy parameter , Prandtl number Pr, and magnetic Prandtl parameter are investigated. The main finding of the current study is related to the determination of the temperature distribution for each inclination angle. It is seen that a higher amplitude of the heat transfer rate occurs as the surface temperature increases. It is also noticed that the oscillatory magnetic flux becomes more important as the magnetic Prandtl number increases at each position. The present magneto-thermal analysis is significantly important in practical applications such as power plants, thermally insulated engines, and nuclear reactor cooling.
The prediction of crack patterns is one of the main tasks in the field of fracture mechanics in order to prevent the total damage of various materials, particularly Methyl Methacrylate Polymer (PMMA). The few data in the literature underscores the need for additional experiments on PMMA to analyze the performance of the phase-field approach to predict crack trajectories. The main purpose of this study is to verify the accuracy of the phase-field approach with a staggered scheme, based on spectral decomposition, for predicting crack propagation in PMMA specimens by comparing it with the experimental results presented in this work. Based on the tensile test and SEM analysis, this material exhibits brittle behavior. The numerical approach considers cracks as diffuse damage rather than sharp discontinuities, enabling a more accurate representation of brittle fracture processes. Experimental determination of material properties is used in the development of the numerical model. The main aim of these experiments is to explore how variations in load and specific geometries influence fracture initiation and crack trajectory. Consequently, these experiments will establish a dataset to further validate numerical advancements.