We report on the extraction of lignin from willow and its use to manufacture cellulose-lignin fibers as potential precursors for the manufacture of carbon fibers. The lignin from willow was extracted using triethyl ammonium hy-drogen sulphate [Et3NH][HSO4]. The lignin extracted by this process was characterized by ATR-IR and elemental analysis, which indicated a high carbon yield. 1-ethyl-3-methylimidazolium acetate [C2C1im][OAc] was then used as a common solvent to dissolve cellulose and lignin to manufacture lignin-cellulose fiber blends. The Young’s modulus of a 75:25 lignin: cellulose fiber was found to be 3.0 ± 0.5 GPa which increased to 5.9 ± 0.6 GPa for a 25:75 lignin: cellulose blend. From a characterization of the surface morphology, using Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) it was observed that higher lignin content in the fiber blend increased the surface roughness. FT-IR analysis confirmed the presence of aromatic groups related to lignin in the obtained fibers from the presence of peaks located at ~1505 cm-1 and ~1607 cm-1. The presence of lignin improves the thermal stability of the fiber blends by allowing them to degrade over a wider temperature range. The presence of lignin also improved the carbon yield during carbonization of cellulose lignin fibers. Therefore the lignin-cellulose fiber developed in this work can offer an excellent alternative to pure cellulose or pure lignin fibers use as precursors carbon fibers.

Alginate is a linear biodegradable polysaccharide polymer, which is bio-renewable and widely used for various biomedical applications. For the next generation of medical textiles, alginate nanofibres are desirable for their use in wound dressings that are biocompatible, sustainable, and abundantly available. This study has developed a unique manufacturing process for producing alginate nanofibres with exceptional antimicrobial properties of oregano essential oil (OEO) as a natural antimicrobial agent. OEO with varying degrees of concentration was incorporated in an aqueous alginate solution. Appropriate materials and electrospinning process parameter selection allowed us to manufacture alginate fibres with a range of diameters between 38 and 105 nm. A unique crosslinking process for alginate nanofibres using extended water soaking was developed. Mechanical characterisation using micro-mechanical testing of nonwoven electrospun alginate/oregano composite nanofibres revealed that it was durable. An extensive antimicrobial study was carried out on alginate/oregano composite nanofibres using a range of Gram-positive (methicillin-resistant Staphylococcus aureus (MRSA) and Listeria monocytogenes) and Gram-negative bacteria (Klebsiella pneumoniae and Salmonella enterica), which are common wound and food pathogens. The results indicated that increasing the concentration of OEO from 2 to 3 wt % showed improved antimicrobial activity against all pathogens, and activity was significantly improved against MRSA compared to a non-alginate-based control disk containing OEO. Therefore, our research suggests that all-natural alginate/oregano nanofibre composite textiles offer a new generation of medical textiles for advanced wound dressing technology as well as for food packaging applications.

European union end of life vehicle directive mandates the use of more sustainable/recyclable materials in automotive industries. Thermoplastics matrix-based composites allow recyclability of composites at the end of life; however, their processing technology is more challenging than thermoset composites. Manufacturing process and mechanical testing of sustainable sandwich composite made from sustainable materials: flax, recycled carbon fiber, polypropylene, and recycled PET foam are presented in this article. High pressure compression molding with adhesive thermoplastic polymer film was used for manufacturing sandwich composite skin. The recycled PET foam core was integrated/joined with the skin using a thermoplastics adhesive film. A three-point bending test was conducted to compare the flexural properties. The results show that such sustainable sandwich composites will be an excellent material for truck side panel to operate in adverse wind/storm conditions. The sustainable sandwich composite can potentially be an excellent candidate for the fabrication of light-duty, lightweight, and low-cost engineering structures in automotive industry to meet the EU end of life requirements.

All chronic wounds are colonised by bacteria; for some, colonisation progresses to become infection. Alginate wound dressings are used for highly exuding chronic wounds as they are very absorbent, taking up large quantities of exudate while maintaining a moist wound bed to support healing. Some alginate dressings are doped with antimicrobials, most commonly silver, but evidence regarding the efficacy of these is largely inconclusive. This manuscript describes the development and in vitro assessment of alginate materials doped with chlorhexidine hexametaphosphate (CHX-HMP), a sparingly soluble salt which when exposed to aqueous environments provides sustained release of the common antiseptic chlorhexidine. Comparator materials were a commercial silver alginate dressing material and an alginate doped with chlorhexidine digluconate (CHXdg). CHX-HMP alginates provided a dose-dependent CHX release which was sustained for over 14 days, whereas CHXdg alginates released limited CHX and this ceased within 24 h. CHX-HMP and silver alginates were efficacious against 5 major wound pathogens (MRSA,E. coli, P. aeruginosa, K. pneumoniae, A. baumannii) in a total viable count (TVC) and an agar diffusion zone of inhibition (ZOI) model. At baseline the silver alginate was more effective than the CHX-HMP alginate in the TVC assay but the CHX-HMP alginate was the more effective in the ZOI assay. After 7 days’ artificial aging the CHX-HMP alginate was more effective than the silver alginate for four of the five bacteria tested in both assays. These materials may ultimately find application in the development of wound dressings for chronic wounds that provide sustained antimicrobial protection.

The consideration of biopolymers with natural products offers promising and effective materials with intrinsic and extrinsic properties that are utilized in several applications. Electrospinning is a method known for its unique and efficient performance in developing polymer-based nanofibers with tunable and diverse properties presented as good surface area, morphology, porosity, and fiber diameters during fabrication. In this work, we have developed an electrospun sodium alginate (SA) incorporated with pulverized Moringa oleifera seed powder (PMO) as a potential natural biosorbent material for water treatment applications. The developed fibers when observed using a scanning electron microscope (SEM), presented pure sodium alginate with smooth fiber (SAF) characteristics of an average diameter of about 515.09 nm (±114.33). Addition of pulverized Moringa oleifera at 0.5%, 2%, 4%, 6%, and 8% (w/w) reduces the fiber diameter to an average of about 240 nm with a few spindle-like pulverized Moringa oleifera particles beads of 300 nm (±77.97) 0.5% particle size and 110 nm (±32.19) with the clear observation of rougher spindle-like pulverized Moringa oleifera particle beads of 680 nm (±131.77) at 8% of alginate/Moringa oleifera fiber (AMF). The results from the rheology presented characteristic shear-thinning or pseudoplastic behaviour with a decline in viscosity, with characteristic behaviour as the shear rate increases, indicative of an ideal polymer solution suitable for the spinning process. Fourier transform infrared spectroscopy (FT-IR) shows the presence of amine and amide functional groups are prevalent on the alginate-impregnated moringa with water stability nanofibers and thermogravimetric analysis (TGA) with change in degradation properties in a clear indication and successful incorporation of the Moringa oleifera in the electrospun fiber. The key findings from this study position nanofibers as sustainable composites fiber for potential applications in water treatment, especifically heavy metal adsorption.

Africa is the third-richest continent in the world in terms of bamboo species. Despite these laudable natural resources, most African countries still use asbestos cement board as one of their major building materials. This is chiefly due to the high cost of equipment and technologies associated with non-asbestos-fiber cement board production. The current research seeks to underscore the possibility of utilizing these massive continent resources for non-asbestos-fiber cement board production by employing the existing production process in the asbestos cement industries via an innovatively developed laboratory-simulated Hatschek process. Non-asbestos-fiber cement boards incorporating kraft and bamboo fibers were successfully produced in the laboratory using this innovative method based on Hatschek technology, with natural fibre addition in the range of 2–6 wt.%. Experimental results revealed that the Flexural strength and deflection of the board improved significantly, producing optimum values of 10.41 MPa and 2.0 mm, respectively for composite board reinforced with 10 wt.% and 6 wt.% of kraft pulp and bamboo fibers, respectively. The SEM morphology of the fractured surfaces revealed the mode of composite fracture as well as good interaction at the fiber–matrix interface. Overall, the mechanical properties of the developed composite boards satisfy the minimum requirements of relevant standards based on fiber cement flat sheets and can be employed for internal building applications in low-cost housing estates in developing countries. The outcome of this research indicates that the current industrial production process based on Hatschek technology can be employed for non-asbestos-fiber cement board production using the studied natural fiber.