An ecofriendly approach was developed for preparing copper-doped carbon dots (CDs) with superior photocatalysis using chromium-copper-arsenic (CCA)-treated wood waste as a precursor. Original wood (W-CDs), CCA-treated wood (C-CDs), and bioremediation CCA wood (Y-CDs) were used as the precursors. The chemical composition and structural, morphological, and optical properties, as well as the photocatalytic ability of the synthesized CDs varied with wood type. The C-CDs and W-CDs had similar characteristics: quasispherical in shape and with a diameter of 2 to 4.5 nm. However, the Y-CDs particles were irregular and stacked together, with a size of 1.5–3 nm. The presence of nitrogen prevented the formation of an aromatic structure for those CDs fabricated from bioremediation CCA wood. The three synthesized CDs showed a broad absorption peak at 260 nm and a weak absorption peak at 320 nm. Proof of the model study for the fabrication of luminescent CDs from CCA wood waste for bioimaging was provided. The degradation rate of CD photocatalytic MB was 97.8% for 30 min. Copper doping gives the CDs electron acceptor properties, improving their photocatalytic efficiency. This study provides novel ways to prepare nanomaterials from decommissioned wood as a nontoxic and low-cost alternative to fluorescent dots.

Developing novel eco-friendly broad-spectrum visible light photocatalysts for dye removal is one of the urgent problems for water treatment. Here, copper-doped carbon dots (CDs) were reported to be directly fabricated from chromated copper arsenate (CCA) wood waste for the photocatalytic degradation of the methylene blue dye. The properties of the resulting CDs were thoroughly characterized and analyzed, preceding an investigation into the adsorption kinetics of dye degradation. The kinetic study showed that reactant concentration was the rate-limiting factor. The obtained CDs showed a 151 mg/g photocatalytic degradation capacity. Comparing pure CDs to CDs/TiO₂ composites, the former demonstrated higher photodegradation efficiency. This superiority can be attributed to the synergistic action of adsorption and photocatalytic degradation working in tandem. This study prepared Cu doped CDs and elucidated the photocatalysis mechanism of methylene blue degradation by CDs. The photodegradation of organic dyes through CDs derived from waste CCA wood emerges as an eco-friendly, facile, and highly efficient method.

Demand for high-performance biocomposites is increasing due to their ease of processing, low environmental impact, and in-service performance. This study investigated the effect of boric acid modification of wood flour on polycarbonate (PC) wood composites’ thermal stability, fire retardancy, water absorption, and creep behavior. The composites’ fire retardancy increased with increasing wood flour content, and their char residue increased by 102.3% compared to that of pure PC. However, the water absorption of the resulting composites increased due to the hydroxyl groups of the wood flour. Wood flour also improved the composites’ anti-creep properties. The excellent fire retardancy and anti-creep properties of wood–PC composites expand their use in the construction sector.

The flame retardancy of wood–polymer composites significantly affects their potential applications. Thus, multilayered wood flour/high-density polyethylene (HDPE)/polycarbonate (PC) composites were prepared via thermocompression to improve the fire retardancy of wood–polymer composites in this paper. Thermal degradation behavior, flame retardancy, and flexural strengths of the resulting composites were investigated using a thermogravimetric analysis, cone calorimetry, and mechanical testing machine, respectively. Results revealed that the boric acid treatment reduced the heat release rate and total heat release of the wood flour/HDPE composites and increased their mass of residues. However, boric acid reduced the flexural strength of the resulting composites. The combustion test indicated that PC cap layers suppressed the combustion of the resulting composites via the formation of carbon layers. Adding PC layers reduced heat release and increased the flexural strength of the resulting composites. Finally, the failure mode of the multilayered wood flour/HDPE/PC composites in the three-point flexural test was simulated by finite element analysis.

Bioremediation is an effective way to remove heavy metals from pollutants. This study investigated the effects of Yarrowia lipolytica (Y. lipolytica) on the bioremediation of chromated copper arsenate (CCA)-treated wood wastes. Copper ions stressed the yeast strains to improve their bioremediation efficiency. A comparison of changes in morphology, chemical composition, and metal content of CCA wood before and after bioremediation was conducted. The amount of arsenic (As), chromium (Cr), and copper (Cu) was quantified by microwave plasma atomic emission spectrometer. The results showed that yeast strains remained on the surface of CCA-treated wood after bioremediation. The morphologies of the strains changed from net to spherical because of the Cu²⁺ stress. Fourier-transform infrared spectroscopy showed that carboxylic acid groups of wood were released after removing heavy metals. A large amount of oxalic acid was observed when the optical density (OD_600nm) was 0.05 on the 21st day. Meanwhile, the highest removal rate of Cu, As, and Cr was 82.8%, 68.3%, and 43.1%, respectively. Furthermore, the Cu removal from CCA-treated wood increased by about 20% after Cu²⁺ stress. This study showed that it is feasible to remove heavy metals from CCA-treated wood by Y. lipolytica without destroying the wood structure, especially by copper-induced Y. lipolytica.