Ivo Dekker

Mr. Ivo Dekker

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2023 in Robotics
Verified
Journal Article
Open access
PDF file
IDIvo Dekker
Ivo Dekker
KKKarel Kellens
Karel Kellens
EDEric Demeester
Eric Demeester
Industrial robots are capable of performing automated tasks repeatedly, reliably and accurately. However, in some scenarios, human-in-the-loop control is required. In this case, having an intuitive system for moving the robot within the working environment is crucial. Additionally, the operator should be aided by sensory feedback to obtain a user-friendly robot control system. Haptic feedback is one way of achieving such a system. This paper designs and assesses an intuitive teleoperation system for controlling an industrial 6-DoF robotic manipulator using a Geomagic Touch haptic interface. The system utilises both virtual environment-induced and physical sensor-induced haptic feedback to provide the user with both a higher amount of environmental awareness and additional safety while manoeuvering the robot within its working area. Different tests show that the system is capable of fully stopping the manipulator without colliding with the environment, and preventing it from entering singularity states with Cartesian end effector velocities of up to 0.25 m/s. Additionally, an operator is capable of executing low-tolerance end effector positioning tasks (∼0.5 mm) with high-frequency control of the robot (∼100 Hz). Fourteen inexperienced volunteers were asked to perform a typical object removal and writing task to gauge the intuitiveness of the system. It was found that when repeating the same test for a second time, the participants performed 22.2% faster on average. The results for the second attempt also became significantly more consistent between participants, as the inter quartile range dropped by 82.7% (from 52 s on the first attempt to 9 s on the second).

7 June 2024 in Journal of Pharmaceutical Innovation
Verified
Journal Article
Open access
PDF file
IDIvo Dekker
Ivo Dekker
PWPieter Waelbers
Pieter Waelbers
WTWido Tancer
Wido Tancer
KKKarel Kellens
Karel Kellens
EDEric Demeester
Eric Demeester
Purpose: Although pharmaceutical high-speed filling lines are fully automated, interventions are still performed by hand via glove ports. Bringing robots into the high-speed production lines for the handling of interventions could increase both the thoughput and the sterility of the system. The work presented in this manuscript proposes a semi-autonomous intervention strategy for the removal of erroneous plungers. Methods: A YOLOv8-based computer vision algorithm continuously monitors the state of the plunger feed. Autonomous motion planning is used for large, general movements, while human-operated teleoperation with system guidance allows for small, precise motions. The combination of both creates a intuitive, gloveless intervention method. Results: A user test with a group of 22 volunteers shows that an untrained operator can perform the teleoperated intervention via this system in an average of $$\pm 30$$ ± 30 s and $$\pm 21$$ ± 21 s when the plungers are static and dynamic respectively. Via a Likert-scale based questionnaire, it was found that the test group experienced the haptic system as very intuitive. Additionally, the system is capable of running completely remotely via a two-laptop setup, which has been tested at distances up to 100km. Conclusion: An intuitive, haptic semi-autonomous teleoperation system is created for the execution of a plunger removal intervention. Both in a static and dynamic scenario, an improvement of the operating time is observed compared to the current glove-based method (2 to 3 min). The system can run fully remotely and was found to be very intuitive by the user group.

11 May 2026 in Robotics
Verified
Journal Article
Open access
PDF file
LKLander Ketelbuters
Lander Ketelbuters
BEBart Engelen
Bart Engelen
IDIvo Dekker
Ivo Dekker
KKKarel Kellens
Karel Kellens
This paper highlights the state of the art in Cooperative Dual-Manipulation (CDM) and Cooperative Multi-Manipulation (CMM), comparing advances in modeling, control, planning, sensing, vision, and end-effector technologies. Methods originally established in CDM have been extended or adapted to support higher complexity of CMM. A historical timeline visualizes the steady growth of cooperative manipulation (CM) and the recent acceleration of CMM driven by rising process complexity and the need for more flexible automation strategies. CM is becoming increasingly relevant as industrial processes demand higher payload capacity, larger workspaces, and greater flexibility. In addition, this paper categorizes existing applications by cooperation type and application domain. Here, a clear dominance of simultaneous object manipulation tasks is visible (fixation-fixation). However, fixation-tooling tasks, where one manipulator grasps the product while another performs a tool operation, and tooling-tooling tasks, where multiple manipulators perform tool operations simultaneously, remain significantly underrepresented. A similar imbalance is found for rigid/non-deformable object manipulation and flexible/deformable object manipulation, respectively. Based on this review, several research gaps are identified: (i) reliable flexible object manipulation methods; (ii) CM strategies for disassembly (e.g., battery pack deconstruction); (iii) complexity in control and planning for multi-manipulator systems; (iv) pathways to industrial deployment beyond laboratory demonstrators; and (v) task-specific tooling and end-effector innovation.

3 February 2026 in Journal of Pharmaceutical Innovation
Verified
Journal Article
Open access
PDF file
GSGert Schouterden
Gert Schouterden
IDIvo Dekker
Ivo Dekker
AMAnton Melnikov
Anton Melnikov
RVRafaël Verbiest
Rafaël Verbiest
DSDavid De Schepper
David De Schepper
KKKarel Kellens
Karel Kellens
This paper presents a comprehensive optimisation and evaluation of an automated de-bagging process for aseptic manufacturing, where a double-bagged product must be transferred from a non-sterile to a highly sterile environment. The current system experiences a high failure rate, with a success rate of only \(\varvec{30~\%}\) in the initial de-bagging step, leading to significant product loss and production downtime. Through a series of empirical, mechanical, and push-out force-based optimisations, including improvements to the product guide rails, clamping mechanisms, and pusher bar operation the success rate of the de-bagging process was increased to \(\varvec{89~\%}\). Based on the results a set of generalised recommendations was formalised for the design of other de-baggers. Part of the suggested optimisation methods have since been integrated in a real de-bagger setup, which shows similar results to those achieved in the test setup.