The strategic initiative aimed at building “digital metallurgy” implies the introduction of diagnostic monitoring systems to trace the technical condition of critical production units. This problem is relevant for rolling mills, which provide the output and determine the quality of products of metallurgical companies. Making up monitoring systems requires the development of digital shadows and coordinate observers, the direct measurement of which is either impossible or associated with numerous difficulties. These coordinates include the spindle torque applied by the spring-transmitting torque from the motor to the rolling stand rolls. The development and research are conducted by the example of the electromechanical systems of the horizontal stand at the plate mill 5000. The stand electric drive characteristics are given, and the emergency modes that cause mechanical equipment breakdowns are analyzed that. The relevance of analyzing transient torque processes in emergency modes has been accentuated. The paper points to the shortcomings of the system for elastic torque direct measurement, including low durability due to the harsh operating conditions of precision sensors. It also highlights the need to install the measuring equipment after each spindle. The disadvantage of the previously developed observer is the function of calculating the electric drive speed derivative. This causes a decrease in noise immunity and signal recovery accuracy. The contribution of this paper is building a digital elastic torque observer that has advantages over conventional technical solutions, based on the theoretical and experimental studies. The technique for virtual observer adjustment was developed and tested in the Matlab-Simulink software package. For the first time, a comprehensive analysis was conducted for spindle elastic torques in emergency modes that caused equipment damage. An algorithm was developed for an emergency shutdown of a stand electric drive in the worst-case mode of strip retraction between work and backup rolls, due to the overlap of the strip on the roll. Further, the algorithm was tested experimentally. The criteria for diagnosing pre-emergencies was then justified. An adaptive motor-braking rate controller was developed. The developed observer and emergency braking system are in operation at the mill 5000. Long experimental research proved the efficiency of dynamic load monitoring and the reduction in the number of equipment breakdowns.

This paper substantiates why it is necessary to limit the dynamic loads in stand shafts when closing angular gaps. The paper is a feasibility study of a concept developed specifically to limit each of the factors that affect amplitude of the dynamic torque; limitations applied are determined on a case-by-case basis. The research team studied the components of elastic torque in a dual-mass electromechanical system of Mill 5000 caused by vibrations arising from the elasticity of transmission as well as from the vibrations caused by elastic collision itself. It is shown that the lowest possible pre-acceleration is necessary for decreasing the dynamic coefficient at a near-nominal load torque. A principle of limiting dynamic loads when closing an angular gap is proposed, which implies collecting tachograms of an electric drive subjected to positive or negative acceleration before and after the fed metal is captured. The research team has developed drive control principles to implement this approach. The recommendation is to upgrade the electric drives of the reversing stand in Mill 5000.

Creating digital twins of industrial equipment requires the development of adequate virtual models, and the calculation of their parameters is a complex scientific and practical problem. To configure and digitally commission automated drives, two-mass electromechanical system models are used. A promising area in which to implement such models is the development of digital shadows, namely drive position observers. Connecting virtual models for online data exchange predetermines the tightening of requirements for their parameter calculation accuracy. Therefore, developing accessible techniques for calculating electromechanical system coordinates is an urgent problem. These parameters are most accurately defined by experiments. The contribution of this paper is the proposition of a method for defining the two-mass system model parameters using the oscillograms obtained in the operating and emergency modes. The method is developed for the horizontal stand drives of a plate mill 5000 and is supported by numerical examples. The technique is universal and comprises calculating the rotating mass inertia torques, elastic stiffness and oscillation damping coefficients, and the time constants of the motor air gap torque control loop. The obtained results have been applied to the development of the elastic torque observer of the rolling stand’s electromechanical system. A satisfactory coordinate recovery accuracy has been approved for both open and closed angular gaps in mechanical joints. Recommendations are given for the use of the method in developing process parameter control algorithms based on automated drive position observers. This contributes to the development of the theory and practice of building digital control systems and the implementation of the Industry 4.0 concept in industrial companies.

This article outlines the relevance of building online telemetry systems for online monitoring of the technical conditions of rolling mill equipment. Electromechanical systems of the horizontal stand of the plate Mill 5000 are described, when operating in harsh conditions caused by the shock loading when workpieces enter the stand. It is noted that dynamic torque overloads, exceeding the rated motor torque by many-fold, cause the fatigue failure of spindle joints and breakage of rolls. In this regard, the development and implementation of systems for monitoring the elastic torque on spindles are extremely urgent. This issue has long been studied, but the references provide no information on the building principles and hardware composition of such systems. The use of strain gauges connected according to a balanced bridge circuit to measure the elastic torque is justified. This paper’s contribution is the proposed modular principle for building a telemetry monitoring system based on the analysis of known techniques for measuring and transmitting diagnostic data. The developed system structure is provided and the concept of data transfer and processing are explained. This article suggests the inductive power supply of a measuring unit mounted on a shaft without the use of batteries. A hardware structure was developed to be applied in a system for measuring, transmitting, and visualizing signals proportional to the elastic torque, manufactured on the basis of data measuring instruments by leading companies. The specifics of placement and connection of strain gauges are considered. The hardware providing a wireless power supply to the signal encoder and digital data transfer between the transmitter and receiver is described. The results of implementing the system on Mill 5000 are provided. The installation of a telemetry ring and a receiving head for the inductive power supply and data reception is shown. An experimental assessment of the elastic torques occurring when workpieces enter the cage was obtained by implementing a drive control algorithm which provided biting in the drive acceleration mode. The reliability of measuring the elastic torque with an error not exceeding ±5% and the reduction of dynamic loads on the spindle by 1.3–1.5 times due to the elimination of impacts from closing angular gaps in spindle joints was confirmed. This increases the service life of mechanical equipment and reduces the cost of eliminating the accident aftermath. The prospect of modifying the developed system into a cyber-physical system for monitoring the rolling mill’s mechatronic equipment conditions is shown.

The development of ferrous metallurgy, as with most industrial sectors, is progressing toward the adoption of IIoT technologies and the development of digital automatic control systems for electrotechnical and mechatronic complexes. This direction is implemented within the paradigm of digital twins (DTs), which enable the use of advanced design methods, virtual commissioning, and maintenance. The concept of relatively simple object-oriented DTs created using available software and applicable at individual stages of the equipment lifecycle has been substantiated. The relationship between the object-oriented approach and M. Grieves’ classification system has been determined. The contribution of this paper lies in the fact that this problem is addressed for the first time using the example of electrotechnical systems of rolling mills. Definitions of DTs are provided, along with a brief overview of digital platforms developed by leading manufacturers of metallurgical equipment. The development of object-oriented DTs based on Simulink Real-Time modules and domains of the Simscape library is substantiated. A methodology for their virtual tuning using Hardware-in-the-Loop (HIL) simulation is proposed. The results of developing an aggregated DT of interconnected electric drives of the upper and lower rolls (UMD and LMD) of the horizontal stand of the 5000 plate rolling mill are presented. An example of DT implementation in a programmable logic controller (PLC) based on a multicore processor using CODESYS 3.5 software is provided. The advantages and prospects of this approach are discussed. Validation of the results is performed by comparing processes during virtual tuning with oscillograms obtained from the actual mill. Satisfactory accuracy is confirmed, and recommendations for the broader application of the developed object-oriented digital twins are given.