This article presents an area-efficient and fast-transient capless low-dropout regulator (LDO) with satisfactory static and dynamic performance in the full load current range. Active-capacitor frequency compensation strategy with push–pull charging ability is employed to reduce on-chip compensation cap without degrading loop stability at light load and improve transient response speed simultaneously. Moreover, in order to drive this compensation capacitance, it makes use of an adaptively biased signal- and transient-current boosting error amplifier as well as transient enhancement circuit with nonlinear control to achieve high loop gain/bandwidth and slew rate. The proposed LDO is implemented in a 0.35-μm 5V-CMOS process and occupies an active chip area of 0.077 mm 2 . Experimental results demonstrate that it can deliver 100-mA load current at 200-mV dropout voltage ( V IN = 2.7–3.3 V, C load ≤100 pF). It consumes 66- μ A quiescent current at light load and can recover within 0.7 μ s for load transient. The voltage spikes at the output, undergoing a maximum load current change, are controlled well below 260 mV and good line/load regulation is achieved synchronously.
22 May 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
A curvature-compensated resistor-less bandgap reference (BGR), which is fabricated in 0.5-μm CMOS process, is proposed in this paper. The BGR utilizes successive voltagestep compensation to produce a temperature-insensitive voltage reference (VR), including one AVGS step for first-order compensation and another one for higher order curvature correction. Moreover, a supply noise bypassing technique is adopted to achieve good power supply rejection performance up to high frequency. Experimental results demonstrate that this BGR is able to produce a VR of 1.196 V with a temperature coefficient of 3.98 ppm/°C at 3.6-V supply voltage. A power-supply noise attenuation of -84 dB@100 Hz and -37 dB@100 kHz are easily achieved, and the line regulation is better than 0.19 mV/V when supply voltage varies from 2.1 to 5 V. The proposed reference occupies an active area of 356 μm × 150 μm and consumes a quiescent current of 38 μA.
3 April 2020 in IEEE Transactions on Power Electronics
An advanced smooth pole tracking technique for low dropout regulator (LDO) with a ceramic capacitor is presented in this paper. Normally, the dominant pole is at the output of LDO and becomes load dependent, which may cause loop stability issue during the whole load-current application range. The proposed frequency compensation methodology with adaptive load resistor control of error amplifier (EA) alleviates the problem and reduces the dependence of equivalent series resistance (ESR) of output capacitor. Moreover, combined with this compensation strategy, an ultra-fast EA by utilizing transconductance enhancement technique is proposed to greatly reduce output voltage spikes as well as response time of the LDO during transient. This circuit has been implemented in a 0.18μm standard CMOS process and occupies an active chip area of 0.017mm $^{2}$ . Experimental results show that it can deliver 150mA load current at 200mV dropout voltage. Good loop stability and transient responses are easily achieved without degrading other important LDO parameters.
9 December 2018 in IEEE Transactions on Power Electronics
Constant on-time control has been widely used due to its advantages of fast transient response and light load efficiency. However, the control scheme is intrinsically unstable if the output capacitor's equivalent series resistance (ESR) is not large enough, which needs ripple injection techniques to enhance loop stability. The traditional passive ripple compensation technique uses only passive component networks to realize this function, which exhibits some inherent shortcomings, including difficulties in high-speed current sensing amplifier design and large chip area consumption. This paper proposes an internal active ripple compensation strategy that senses the low-side power mosfet current and extracts relevant ac information for feedback-ripple enhancement. Output-voltage dc offset does not occur and subharmonic instability is significantly improved even with ceramic capacitors. The circuit architecture has been realized in a synchronous buck regulator with a 0.5 μm 40 V bipolar-CMOS-DMOS (BCD) process. The programmable switching frequency is up to 1 MHz and the maximum load current is 4 A. Simulation and experimental results are given to prove the proposed high performance.
28 August 2023 in IEEE Journal of Solid-State Circuits
A current-efficient and fast-transient n-type low-dropout regulator (LDO) for high-frequency load transient in mobile phone applications is presented in this article. By using transconductance magnified MOS (TM-MOS), it reduces LDO’s output impedance with fast response speed and keeps high current efficiency. Moreover, based on load-current sensing of TM-MOS, active clamp strategy is implemented to optimize the driving dead zone (DDZ) of this NMOS LDO and achieve good high-frequency load transient performance. Robust loop stability for a wide load-current range is ensured as well with the help of revised Type-II frequency compensation. This circuit has been implemented in a 0.35- $\mu$ m standard CMOS process and occupies an active chip area of 470 $\times$ 280 $\mu$ m $^{2}$ . With a 1- $\mu$ F output cap and load steps between 0 A and 300 mA, experimental results show that it features 50/36 mV of undershoot/overshoot at low-frequency load transient and 68/36 mV of undershoot/overshoot at the high-frequency load transient (i.e., 10- $\mu$ s light-load duration). This regulator consumes 8.2- $\mu$ A quiescent current, achieving 99.68% equivalent current efficiency at 300-mA load current.
11 March 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
A fast-transient, current-efficient low-dropout regulator (LDO) with super transconductance cell (STC) is proposed in this paper. By adopting advanced current amplifier (CA) and dynamic biasing (DB) techniques for the error amplifier (EA), the feedback loop bandwidth can be significantly extended without increasing much quiescent power, which reduces output voltage spikes and response time greatly. Moreover, dynamic reference control (DRC) with robust loop stability is embedded in the LDO to adaptively adjust voltage reference during transient so as to further enhance the slew rate of EA, realizing significant enhancement for the transient performances. This circuit has been implemented in a 0.35μm CMOS process and occupies an active chip area of 456×278 μm 2 . Experimental results show that it is able to provide 100mA load current at 200mV dropout voltage, with current efficiency of 99.88%. The output voltage spike under maximum load current change in 20ns edge time is less than 11.2mV with a 0.054μs response time. The power-supply rejection (PSR) at 100kHz is -75.6dB.