Xilin Zhou

Prof. Dr. Xilin Zhou

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 August 2021 in Nature Communications
Verified
Journal Article
Open access
PDF file
YGYicheng Guan
Yicheng Guan
XZXilin Zhou
Xilin Zhou
FLFan Li
Fan Li
TMTianping Ma
Tianping Ma
SYSee-Hun Yang
See-Hun Yang
SPStuart S. P. Parkin
Stuart S. P. Parkin
The current induced motion of domain walls forms the basis of several advanced spintronic technologies. The most efficient domain wall motion is found in synthetic antiferromagnetic (SAF) structures that are composed of an upper and a lower ferromagnetic layer coupled antiferromagnetically via a thin ruthenium layer. The antiferromagnetic coupling gives rise to a giant exchange torque with which current moves domain walls at maximum velocities when the magnetic moments of the two layers are matched. Here we show that the velocity of domain walls in SAF nanowires can be reversibly tuned by several hundred m/s in a non-volatile manner by ionic liquid gating. Ionic liquid gating results in reversible changes in oxidation of the upper magnetic layer in the SAF over a wide gate-voltage window. This changes the delicate balance in the magnetic properties of the SAF and, thereby, results in large changes in the exchange coupling torque and the current-induced domain wall velocity. Furthermore, we demonstrate an example of an ionitronic-based spintronic switch as a component of a potential logic technology towards energy-efficient, all electrical, memory-in-logic.

20 April 2022 in Nano Letters
Verified
Journal Article
Open access
MWMohamed Amine Wahada
Mohamed Amine Wahada
ESErsoy Sasioglu
Ersoy Sasioglu
WHWolfgang Hoppe
Wolfgang Hoppe
XZXilin Zhou
Xilin Zhou
HDHakan Deniz
Hakan Deniz
GWGeorg Woltersdorf
Georg Woltersdorf
Ferromagnet/heavy metal bilayers represent a central building block for spintronic devices where the magnetization of the ferromagnet can be controlled by spin currents generated in the heavy metal. The efficiency of spin current generation is paramount. Equally important is the efficient transfer of this spin current across the ferromagnet/heavy metal interface. Here, we show theoretically and experimentally that for Ta as heavy metal the interface only partially transmits the spin current while this effect is absent when Pt is used as heavy metal. This is due to magnetic moment reduction at the interface caused by 3d-5d hybridization effects. We show that this effect can be avoided by atomically thin interlayers. On the basis of our theoretical model we conclude that this is a general effect and occurs for all 5d metals with less than half-filled 5d shell.

13 April 2018 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
JBJitendra K. Behera
Jitendra K. Behera
XZXilin Zhou
Xilin Zhou
ARAlok Ranjan
Alok Ranjan
RSRobert E. Simpson
Robert E. Simpson

1 July 2025 in Nature Communications
Verified
Journal Article
Open access
PDF file
JZJia Zheng
Jia Zheng
RWRuobing Wang
Ruobing Wang
WFWencheng Fang
Wencheng Fang
CLChengxing Li
Chengxing Li
JZJiarui Zhang
Jiarui Zhang
ZSZhitang Song
Zhitang Song
Phase change memory has been regarded as a promising candidate for storage class memory application. However, the high switching current and limited switching endurance remain a critical challenge. In this work a switching endurance beyond 1.1 × 1011 cycles is demonstrated in the mushroom-type memory device with nano-cofined structure and carbon-doped GeSbTe material. The over-programming of the memory cell induced by excessive RESET current gives rise to the recrystallization of the active phase change volume which accelerates the inward migration of carbon atoms to the bottom heater. The cyclic switching exacerbates the over-programming effect with denser carbon cluster accumulated at the boundary of the active region which causes the stuck-RESET failure. The nano-confined cell structure enables efficient heating by relocating the melt-quench region away from the interface to the dielectric layer which substantially reduces the RESET energy and, consequently, mitigates the over-programming effect and significantly extends the switching cycles.

13 May 2024 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
MZMengyu Zhang
Mengyu Zhang
RWRuobing Wang
Ruobing Wang
XZXixi Zou
Xixi Zou
SSSannian Song
Sannian Song
YBYun Bao
Yun Bao
XZXilin Zhou
Xilin Zhou
The Sb2Te3 phase change material shows a growth-dominated crystallization mechanism with fast phase transition but poor thermal stability of the amorphous state. This work investigated the effects of carbon doping on the thermal stability, microstructure, and electrical properties of the Sb2Te3 material. The 10-year data retention temperature of the material increased to ∼147.3 °C and the size of the grains was limited to ∼10 nm by carbon doping. The formation of the C cluster upon crystallization was found at the grain boundaries, which was accelerated as the temperature increased due to the break of the Sb–C bonds. The memory device based on the carbon-doped Sb2Te3 material exhibited a switching speed of 15 ns and an endurance of ∼105 cycles with a resistance ratio of more than two orders of magnitude. This work suggests that the carbon-doped Sb2Te3 material is a promising candidate for memory applications that require high thermal stability, fast speed, and high endurance.

15 March 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
JZJiarui Zhang
Jiarui Zhang
WFWencheng Fang
Wencheng Fang
RWRuobing Wang
Ruobing Wang
CLChengxing Li
Chengxing Li
JZJia Zheng
Jia Zheng
XZXilin Zhou
Xilin Zhou
High density phase change memory array requires both minimized critical dimension (CD) and maximized process window for the phase change material layer. High in-wafer uniformity of the nanoscale patterning of chalcogenides material is challenging given the optical proximity effect (OPE) in the lithography process and the micro-loading effect in the etching process. In this study, we demonstrate an approach to fabricate high density phase change material arrays with half-pitch down to around 70 nm by the co-optimization of lithography and plasma etching process. The focused-energy matrix was performed to improve the pattern process window of phase change material on a 12-inch wafer. A variety of patternings from an isolated line to a dense pitch line were investigated using immersion lithography system. The collapse of the edge line is observed due to the OPE induced shrinkage in linewidth, which is deteriorative as the patterning density increases. The sub-resolution assist feature (SRAF) was placed to increase the width of the lines at both edges of each patterning by taking advantage of the optical interference between the main features and the assistant features. The survival of the line at the edges is confirmed with around a 70 nm half-pitch feature in various arrays. A uniform etching profile across the pitch line pattern of phase change material was demonstrated in which the micro-loading effect and the plasma etching damage were significantly suppressed by co-optimizing the etching parameters. The results pave the way to achieve high density device arrays with improved uniformity and reliability for mass storage applications.