Fused deposition modelling (FDM) is one of rapid prototyping (RP) technologies which uses an additive fabrication approach. Each commercially available FDM model has different types of process parameters for different applications. Some of the desired parts require excellent surface finish as well as good tolerance. The most common parameters requiring setup are the raster angle, tool path, slice thickness, build orientation, and deposition speed. The purpose of this paper is to discuss the process parameters of FDM Prodigy Plus (Stratasys, Inc., Eden Prairie, MN, USA). Various selected parameters were tested and the optimum condition was proposed. The quality of the parts produced was accessed in terms of dimensional accuracy and surface finish. The optimum parameters obtained were then applied in the fabrication of the master pattern prior to silicone rubber moulding (SRM). These parameters would reduce the post processing time. The dimensional accuracy and surface roughness were analyzed using coordinate measuring machine (CMM) and surface roughness tester, respectively. Based on this study, the recommended parameters will improve the quality of the FDM parts produced in terms of dimensional accuracy and surface roughness for the application of SRM.
The concept of repair and restoration using additive manufacturing (AM) is to build new metal layers on a broken part. It is beneficial for complex parts that are no longer available in the market. Optimization methods are used to solve product design problems to produce efficient and highly sustainable products. Design optimization can improve the design of parts to improve the efficiency of the repair and restoration process using additive manufacturing during the end-of-life (EoL) phase. In this paper, the objective is to review the strategies for remanufacturing and restoration of products during or at the EoL phase and facilitate the process using AM. Design optimization for remanufacturing is important to reduce repair and restoration time. This review paper focuses on the main challenges and constraints of AM for repair and restoration. Various AI techniques, including the hybrid method that can be integrated into the design of AM, are analyzed and presented. This paper highlights the research gap and provides recommendations for future research directions. In conclusion, the combination of artificial neural network (ANN) algorithms with genetic algorithms as a hybrid method is a key solution in solving limitations and is the future for repair and restoration using additive manufacturing.
The design for additive manufacturing (DFAM) processing was introduced to fully utilize the design freedom provided by additive manufacturing (AM). Consequently, appropriate design methodologies have become essential for this technology. Recently, many studies have identified the importance of DFAM method utilization to produce AM parts, and theory of inventive problem-solving (TRIZ) is a strategy used to formalize design methodologies. TRIZ is a problem-solving tool developed to assist designers to find innovative and creative solutions. However, the pathway for synergizing TRIZ and DFAM is not clearly explained with respect to AM capabilities and complexities. This is mainly because most methods continue to involve use of the classical TRIZ principle, which was developed early in 1946, 40 years before AM technologies were introduced in the mid-1980s. Therefore, to tackle this issue, this study aims to enhance the 40 principles of classical TRIZ to accommodate AM design principles. A modified TRIZ-AM principle has been developed to define the pathway to AM solutions. TRIZ-AM cards are tools that assist designers to select inventive principles in the early phases of product design and development. The case study illustrates that even inexperienced AM users can creatively design innovative AM parts.
The rise of wire arc additive manufacturing (WAAM) is attributed to the various field applications of additive manufacturing (AM), especially in producing large metal structures. The wire arc additive manufacturing is a process that can produce near-net-shape structures with high deposition rates and relatively lower costs. Due to the nature of the WAAM process, which is based on layer-by-layer fabrication and repeated heating and cooling cycles, surface defects can occur on the deposited layer, such as pores, cracks, oxidation, and geometric deviation. In understanding the factors that can affect the stability and mechanism of the WAAM process, online monitoring systems has been studied by researchers. This paper aims to critically review the different monitoring techniques as well as distinct sensing methods that can be applied in the WAAM process to enhance the quality of the 3D object. In conducting this review paper, the systematic literature review (SLR) method is chosen to enhance a better understanding of the current research works of monitoring systems in the WAAM process. The high heat accumulation and cooling rate process are found to be the most crucial factors that could influence the geometrical accuracy, microstructure, and mechanical properties of the deposited layer.
Five designs of imbricate scale armour features for stab-resistant application were printed via fused deposition modelling process. Stab test on these designs against the HOSDB KR1-E1 stab-resistant body armour standard with impact energy of 24 Joules was conducted. The stab test was conducted on a number of samples measured thicknesses ranging from 4.0 to 10.0 mm by using Instron CEAST 9340 Drop Impact Tower to determine a minimum thickness that resulted in a knife penetration through the underside of sample which does not exceed the maximum penetration permissibility of 7.0 mm. Materials used for the samples were ABS-M30 and PC-ABS. Finally, one of the designs which offered the highest knife penetration resistance was selected. The results show that PC-ABS samples provide less shattering and lower overall knife penetration depth in comparison with ABS-M30. PC-ABS stab test demonstrated a minimum thickness of 8.0 mm, which was the most adequate to be used in the development of FDM manufactured body armour design features. Lastly, the design feature of D5 has shown to exhibit the highest resistance to the knife penetration due to the penetration depth of 3.02 mm, which was the lowest compared to other design features.