In the present study commercial Polylactic Acid-based disposable cups and plates were selected for lab scale anaerobic degradability tests. The experiments were carried out under thermophilic conditions at different inoculum to substrate ratios and test material sizes, and the specific biogas production and associated kinetics were evaluated. Maximum biogas production was comparable for almost all the experimental runs (1620 and 1830 NmL/gTOCPLA) and a biodegradation degree in the range 86-100% was attained. Moreover, physical, chemical and microscopical analyses were used to characterize the tested materials before and after the degradation. The products composition was assessed and the presence of some additives (mainly Ca-based) was detected. Potential correlations among the process parameters and product composition were derived and a delay in process kinetics with increasing amount of additives embedded in the polymeric matrix was observed, confirming the relevant influence of the chemical blend on the biodegradation process.
Bioplastics have entered everyday life as a potential sustainable substitute for commodity plastics. However, still further progress should be made to clarify their degradation behavior under controlled and uncontrolled conditions. The wide array of biopolymers and commercial blends available make predicting the biodegradation degree and kinetics quite a complex issue that requires specific knowledge of the multiple factors affecting the degradation process. This paper summarizes the main scientific literature on anaerobic digestion of biodegradable plastics through a general bibliographic analysis and a more detailed discussion of specific results from relevant experimental studies. The critical analysis of literature data initially included 275 scientific references, which were then screened for duplication/pertinence/relevance. The screened references were analyzed to derive some general features of the research profile, trends, and evolution in the field of anaerobic biodegradation of bioplastics. The second stage of the analysis involved extracting detailed results about bioplastic degradability under anaerobic conditions by screening analytical and performance data on biodegradation performance for different types of bioplastic products and different anaerobic biodegradation conditions, with a particular emphasis on the most recent data. A critical overview of existing biopolymers is presented, along with their properties and degradation mechanisms and the operating parameters influencing/enhancing the degradation process under anaerobic conditions.
Four different end-of-life options for disposable bioplastic cups were investigated and compared based on their environmental implications. Two products with distinct polymeric composition were tested simulating the following scenarios at laboratory scale: i) industrial composting (180 days at 58 °C); ii) anaerobic digestion followed by industrial composting (45 days at 55 °C and 180 days at 58 °C); iii) anaerobic digestion followed by direct digestate use on soil for agricultural purposes (45 days at 55 °C and 180 days at 25 °C); iv) uncontrolled release into a soil environment (180 days at 25 °C). Ecotoxicity tests were run at the end of each experiment to investigate the effects of the materials on three main groups of terrestrial model organisms: plants, earthworms and nitrifying bacteria. Complete biodegradation of the cups was observed in 180 days in the scenarios involving composting environment. A low degree of biodegradation (22.9 ± 4.5%) of the digestates in soil was observed, warning for a potential micro-bioplastics discharge into the environment. No degradation was observed for the cups in soil during the same testing period. Ecotoxicity tests revealed a negative effect on plants biomass growth across all samples, which was 17-30% lower compared to the blank sample. The experimental campaign highlighted the need for a systematic assessment of controlled treatment of bioplastics, as well as the need for a harmonized legislative framework.
The present work investigates a two-stage process scheme for cheese whey valorization through energy recovery in different forms by means of bio-electrochemical systems. The first stage consisted of an integrated bio-electrochemical process for H2 and electricity production. This combined dark fermentation with an electrochemical system with the aim of overcoming the typical thermodynamic/biochemical limitations of fermentation and enhancing H2 recovery. The second treatment stage involved a single-chamber microbial fuel cell, featuring an innovative configuration consisting of four air cathodes with fly ash as the oxygen reduction catalyst. The bio-electrochemical process performed in the first stage achieved promising results, displaying a three-times higher H2 production yield compared to conventional dark fermentation. In addition, the experiments using the MFC in the second stage were found to successfully exploit the effluent from the first stage, with COD removal yields of 86% ± 8% and energy recovery with a maximum current output of 1.6 mA and a maximum power density of 1.2 W/m3.
10 April 2022 in Clean Technologies and Environmental Policy
This study investigated the performance of a novel integrated bio-electrochemical system for synergistic hydrogen production from a process combining a dark fermentation reactor and a galvanic cell. The operating principle of the system is based on the electrochemical conversion of protons released upon dissociation of the acid metabolites of the biological process and is mediated by the electron flow from the galvanic cell, coupling biochemical and electrochemical hydrogen production. Accordingly, the galvanic compartment also generates electricity. Four different experimental setups were designed to provide a preliminary assessment of the integrated bio-electrochemical process and identify the optimal configuration for further tests. Subsequently, dark fermentation of cheese whey was implemented both in a stand-alone biochemical reactor and in the integrated bio-electrochemical process. The integrated system achieved a hydrogen yield in the range 75.5–78.8 N LH2/kg TOC, showing a 3 times improvement over the biochemical process. Graphical abstract