Due to its very high critical fields, the second-generation high-temperature superconductor (2 G HTS) has been, and is being, used in high-field magnets. However, a persistent screening current induced in the REBCO conductor under time-varying conditions distorts the magnetic field, spatially and temporally. We describe a novel REBCO conductor design composed of narrow-stacked (NS) wire, a bundle of 1 mm wide REBCO tapes. The design is based on a fundamental notion that the narrower the REBCO tape width, the smaller the screen-current field (SCF). In this paper, both experimental and simulation work were carried out to analyze SCF in a REBCO coil wound with an NS wire. We demonstrate that the critical current of NS wires can be consistent with the conventional REBCO tape to meet the application requirements. Meanwhile, NS wire indeed substantially results in small SCF, an important requirement in high-field magnets such as for NMR, MRI, and HEP that may rely on REBCO conductor.
A superconducting magnet, which operates in a persistent current mode (PCM), is able to reduce heat loss on current leads, therefore, gradually become promising and important in many industrial usages. To realize the PCM, a persistent current switch (PCS) is an indispensable part, which also greatly influences final charging quality, and PCS has been designed extending to many kinds. In this paper, another kind of PCS is proposed, which is made by a section of tape in a coil. The PCS is triggered by over-current directly from the current source without any additional switching triggers. Performance of the PCS in two different winding conditions (i.e., in an insulated (INS) coil and a no-insulation (NI) coil) are tested. Each coil tails is soldered together as a joint to form a closed current loop. Thus, four experimental cases can be investigated with regards to the four conditions: INS or NI coil with the section (i.e., the PCS) selected including the joint, which is used to form a closed loop or not. Results show that in certain conditions, 95% of source current ultimately flows into the coil, and the PCS is switched off at an optimal threshold value of successfully charging the coil and generating the least heat. Besides, the absence of additional switching triggers can reduce the weight and size of the magnet. Meanwhile, four equivalent electrical circuit models corresponding to the four experimental cases are established and verified.
19 November 2018 in IEEE Transactions on Applied Superconductivity
High temperature superconducting (HTS) Soldered-Stacked-Square (3S) wire has been proposed as a novel potential structure for the second generation (2G) HTS wire. Twisted method is an available way to decrease the anisotropy and improve the performance of 3S wire in high field application. This paper presents a three dimensional (3D) numerical model based on H-formulation for the 3S-twisted (3S-T) wire. AC loss is evaluated as an important parameter when 3S-T wire is applied in alternating current or magnetic field circumstances. Three different structures of 3S-T wires are considered and the validity of the general model is verified by the corresponding experimental results. The results show that there is no significant eddy loss existed in the 3S-T wire. Moreover, if more HTS tapes are contained in 3S-T wires, the current distribution will be closer to elliptical shape and the current phase in different YBCO layers will be changed. The transport AC loss can be slightly reduced through the twisted method. The work in this paper will be helpful to understand the electromagnetic characteristics of 3S-T wire.
1 March 2019 in IEEE Transactions on Applied Superconductivity
Screening current is a persistent current that flows in the wide area of second-generation high-temperature superconducting (2G HTS) coated conductor, which is induced when a 2G HTS magnet is energized. The screening current induced field (SCIF) will cause the reduction and the temporal drift of the center magnetic field in the HTS magnets. This paper reports a novel structure HTS tape with 1 mm width for high precise HTS magnet design. The principle of this tape structure, which is so-called 2s + 1c tape, is to stack two narrow HTS tapes and one copper tape through the soldering furnace. In this paper, we did the experiments of the SCIF hysteresis loop for the coil wound with the 2s + 1c tape and the benchmark coil wound with the commercial 5 mm wide HTS tape. Then, a numerical model for SCIF hysteresis loop was verified by experimental results. Based on the validated model, we analyzed the behavior of SCF to other operating conditions, such as temperature control and current sweep reversal. Finally, the 2s + 1c tape was confirmed as a new approach to reducing the SCIF significantly.