16 November 2018 in IEEE Transactions on Applied Superconductivity
5 February 2018 in IEEE Transactions on Applied Superconductivity
In the high-temperature superconducting (HTS) magnets applications, fast quench detection is very important to protect the magnets from burning out. Usually, the method of voltage measurement is widely applied to detect quench. However, this method is not satisfied for large HTS magnets intrinsically. Besides, a novel quench detection, which is measured by Raman-scattering-based distributed temperature sensors (DTS) using flexible optical fibers, is suggested to be a potential candidate. To verify the feasibility of this method, we prepared a DTS system based on interrogating Raman-scattering signals and a no-insulation (NI) HTS coil mounted by a 2-m length optical fiber as a test sample. The main results show that critical current of the NI coil is 111 A. In the continued overcurrent-induced quench state under coil current of 160 A, the temperature rise was observed obviously at the position of 1.2 m in the optical fiber, and the temperature was up to 94 K in the near middle region of top surface in the NI coil.
16 January 2017 in IEEE Transactions on Applied Superconductivity
High-temperature superconducting (HTS) coils made of coated conductors that can operate in persistent current mode (PCM) are regarded to be promising in MRI/nuclear magnetic resonance and Maglev system. The temporal stability of the magnetic field trapped by the PCM coil is a key issue, which significantly determines the imaging quality of MRI and dynamic behavior of Maglev. This study focuses on the temporal stability of the trapped magnetic field in the double-slit HTS PCM coil, which is magnetized by a field cooling (FC) method at 77 K. The magnetic field decay behavior under different initial fields and FC ramp rates are systematically studied. The experiment results indicate that higher initially trapped field will lead to faster decay, but if the initially trapped field is lower than a certain value, this trend is no longer obvious. The FC ramp rate has a little impact on the field decay. Finally, a numerical model based on R–L circuit and E–J equation is established to fit the decay process. It is found that if the operating current is lower than 60% of the coil critical current, good temporal stability could be achieved. Another long-term experiment is performed that a stability of 8.1 ppm/h is achieved after 19 days’ decay.
25 January 2019 in IEEE Transactions on Applied Superconductivity
Magnetic levitation vehicle (maglev) is a promising candidate for high-speed transportation with features like low pollution and power loss. And the maglev performances are further enhanced by introducing the high-temperature superconducting (HTS) technology to the maglev. In this paper, a 7.55-kW small-scale HTS linear synchronous motor (LSM) is designed as a preparatory research of the propulsion system for the future high-speed maglev. Different from those in a permanent magnet (PM) LSM, the primary and secondary parts are especially designed for an HTS LSM according to the design flow. Performances are analyzed including the comparison between the HTS LSM and the PM LSM. Under the same electromagnetic gap of 10 mm, the maximum propulsive force of the HTS LSM is 1510 N, which is ∼50% larger than that of the PM LSM though the commercial PMs with the strongest remnant field of 1.45 T (N52) are selected and arranged in a Halbach array. And the field waveform of HTS secondary is also more sinusoidal with lower total harmonic distortion. Overall, the HTS LSM performs better than the PM LSM, and the design results can provide possible references for the future high-speed maglev.
26 June 2018 in IEEE Transactions on Applied Superconductivity
A superconducting magnet, which operates in a persistent current mode (PCM), is able to reduce heat loss on current leads, therefore, gradually become promising and important in many industrial usages. To realize the PCM, a persistent current switch (PCS) is an indispensable part, which also greatly influences final charging quality, and PCS has been designed extending to many kinds. In this paper, another kind of PCS is proposed, which is made by a section of tape in a coil. The PCS is triggered by over-current directly from the current source without any additional switching triggers. Performance of the PCS in two different winding conditions (i.e., in an insulated (INS) coil and a no-insulation (NI) coil) are tested. Each coil tails is soldered together as a joint to form a closed current loop. Thus, four experimental cases can be investigated with regards to the four conditions: INS or NI coil with the section (i.e., the PCS) selected including the joint, which is used to form a closed loop or not. Results show that in certain conditions, 95% of source current ultimately flows into the coil, and the PCS is switched off at an optimal threshold value of successfully charging the coil and generating the least heat. Besides, the absence of additional switching triggers can reduce the weight and size of the magnet. Meanwhile, four equivalent electrical circuit models corresponding to the four experimental cases are established and verified.
25 January 2019 in IEEE Transactions on Applied Superconductivity
A small-scale linear propulsion system, made of a linear synchronous motor (LSM), is designed for preparatory researches of the future high-speed maglev. The secondary part of the LSM is made of high-temperature superconducting (HTS) no-insulation (NI) magnets. This paper focuses on the design process and performance analysis of the NI HTS magnets. The design target is to optimize the dimensions of the magnets with minimum HTS tapes consumption while generating a qualified magnetic field and operating the magnets safely. Based on the design results, field and critical current distributions in the different locations of the magnets are investigated to provide references for critical current determination. The magnets are designed to operate at temperature of 30 K with a magneto-motive force of ∼295 kA and stored energy of ∼25 kJ. The average fundamental component of the field at 70 mm beneath the bottom of the magnets is 0.53 T (RMS), and the charging time of the magnets is ∼41 min, with maximum charging loss of 16 W. The design results meet the requirement of the LSM.