An adaptive on/off delay-compensation technique is proposed to improve the performance of CMOS active rectifiers for wireless power transfer (WPT) systems. The effects of the on/off delays on the performance of the active rectifiers with either a parallel-resonant or a series-resonant circuit at the secondary coil are studied, which include power conversion efficiency (PCE), voltage conversion ratio (VCR) and output voltage ripple. By adding two feedback loops to the active diodes to generate the switched-offset currents for the comparators adaptively, both onand off-delays are compensated for accurately against PVT variations and mismatches. As a design example, a fully integrated active rectifier for biomedical applications with a parallel-resonant secondary was fabricated in a standard 0.35 μm CMOS process. With an AC input that ranges from 1.8 to 3.6 V, the measured VCR is higher than 90% and the measured PCE is higher than 89.1% for a load resistor of 500 Ω. In particular, the PCE is increased by 9% compared to the active rectifier without using the proposed technique.
24 February 2017 in IEEE Journal of Solid-State Circuits
A 6.78-MHz wireless power receiver using a 3-mode reconfigurable resonant regulating rectifier for resonant wireless power transfer is presented. The proposed receiver improves power conversion efficiency and reduces die area and off-chip components by achieving power conversion plus voltage regulation in one stage, using only four on-chip power transistors and one off-chip capacitor. Moreover, the proposed 3-mode operation reduces the output voltage ripples and accomplishes switching synchronization easily during mode switching. The proposed pulsewidth modulation controller using ramp-stacking technique and type-II compensation achieves tight voltage regulation in the full loading range with fast transient responses. An adaptive sizing method is also employed to further improve the light-load efficiency of the receiver. Fabricated in a standard 0.35-μm CMOS process using 5-V devices, the receiver regulates the output voltage at 5 V and delivers a maximum power of 6 W. The measured peak efficiency reaches 92.2% when delivering an output power of 3.5 W. For a load step between 0.5 and 5 W, the overshoot and undershoot are less than 300 mV and the settling times are less than 16 μs.
29 August 2014 in IEEE Journal of Solid-State Circuits
A 10/30 MHz voltage-mode controlled buck converter with a wide duty-cycle range is presented. A high-accuracy delay-compensated ramp generator using only low-speed comparators but can work up to 70 MHz is proposed. By using a differential difference amplifier (DDA), a new Type-III compensator is proposed to reduce the chip area of the compensator by 60%. Moreover, based on the unique structure of the proposed compensator, an end-point prediction (EPP) scheme is also implemented to achieve fast reference-tracking responses. The converter was fabricated in a 0.13 μm standard CMOS process. It achieves wide duty-cycle ranges of 0.75 and 0.59 when switching at 10 MHz and 30 MHz with peak efficiencies of 91.8% and 86.6%, respectively. The measured maximum output power is 3.6 W with 2.4 V output voltage and 1.5 A load current. With a constant load current of 500 mA, the up-tracking speeds for switching frequencies of 10 MHz and 30 MHz are 1.67 μs/V and 0.67 μs/V, respectively. The down-tracking speeds for 10 MHz and 30 MHz are 4.44 μs/V and 1.56 μs/V, respectively.
19 August 2016 in IEEE Transactions on Power Electronics
This letter presents a 6.78 MHz wireless power transfer (WPT) system for wirelessly powered flash drives that need multiple supplies with a total power of sub-1 W. A new architecture that merges an N-level single-inductor multiple-output switching converter with a multistage rectifier is proposed for the WPT receiver, and the regulated outputs attain small ripples. A prototype of a 2X active rectifier that merges with a three-level single-inductor dual-output dc-dc converter is implemented in a 0.35 μm CMOS process.
5 August 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents an active rectifier operating at 40.68 MHz for wirelessly powered biomedical implant devices. The commonly used current-injection-based compensation and delay-based compensation schemes are analyzed. To tackle design difficulties at high frequency, a hybrid delay-compensation scheme is proposed to compensate for the turn-on and turn-off delays. The proposed scheme has a simple control logic that results in a power-efficient comparator design. A fully integrated active rectifier was fabricated in a standard 0.18-μm CMOS process with a total area of 1.581 mm² and a maximum output power of 56.6 mW. With the input ac voltage ranging from 2.5 to 4 V and the load resistor ranging from 200 Ω to 2 kΩ , the measured peak voltage conversion ratio and peak power conversion efficiency reach 91% and 80.9%, respectively.
14 January 2020 in IEEE Journal of Solid-State Circuits