On 1 December 2020, China’s Chang’E-5 (CE-5) probe successfully landed in the northeastern Oceanus Procellarum. This work mainly presents the results of Lunar Regolith Penetrating Radar (LRPR) equipped on the CE-5 Lander. The lunar regolith structure of the landing site from the surface to 3-m depth is unveiled by LRPR, which found that abundant rock fragments are distributed in uniform lunar regolith. The imaging result proved that the drilling and sampling process was prevented by big rocks at about 100 cm depth. On the basis of the response of lunar soil to electromagnetic (EM) wave, the EM properties of the landing site estimate that the relative dielectric constant and the loss tangent are 2.520 ± 0.186 and 0.0133 ± 0.0020, respectively.
1 February 2021 in IEEE Aerospace and Electronic Systems Magazine
Sampling return in Chang'E-5 (CE-5) mission is the third phase of three strategic steps of China's lunar program. The three strategic steps are orbiting, landing, and returning. The sampling and drilling device is mounted on the Lander. One task of the CE-5 Lunar Regolith Penetrating Radar (LRPR) is to provide information support for the drilling and sampling device. This article introduces the scientific objectives of CE-5 LRPR and the difference with Chang'E-3 lunar penetrating radar. The system design, working principle, imaging, and calibration methods of LRPR are the highlight. Considering that the Lander is stationary, and its bottom is about 90 cm from the lunar surface, an antenna array is adopted to probe the subsurface structure and the regolith thickness for supporting the drilling. The design uses a pre-amplifier circuit to increase the dynamic range of the whole system, which enhances the detection effect of shallow lunar soil structure. For verifying the probing ability of LRPR, the marble slabs, metal balls, and stones are buried in the volcanic ash pool in advance for detection and verification. The pre-stack Kirchhoff depth migration imaging method is adopted to identify the burial depth and thickness of the target. The verification results meet the task requirements.
Chang’E-7 will be launched around 2026 to explore resources at the lunar south pole. Glaciers are suitable scenes on the earth for lunar penetrating radar verification. In the verification experiment, ice-penetrating signals are inevitably polluted by noise, affecting the accuracy and reliability of glacier detection. This paper proposes a denoising method for ice-penetrating signals based on the combination of whale optimization algorithm (WOA), variational mode decomposition (VMD), and the improved Bhattacharyya distance (BD). Firstly, a fitness function for WOA is established based on permutation entropy (PE), and the number of decomposition modes K and the quadratic penalty factor in the VMD are optimized using WOA. Then, VMD is performed on the signal to obtain multiple intrinsic mode functions (IMFs). Finally, according to the BD, the relevant IMFs are selected for signal reconstruction and denoising. The simulation results indicate the strengths of this method in enhancing the signal-to-noise ratio (SNR), and its performance is better than empirical mode decomposition (EMD). Experiments on the detected signals of the Mengke Glacier No. 29 indicate that the WOA-VMD-BD method can efficiently eliminate noise from the data and procure well-defined layered profiles of the glacier. The research in this paper helps observe the layered details of the lunar regolith profile and interpret the data in subsequent space exploration missions.
A High-speed digital sampling technology suitable for periodical impulse radar signal is proposed in this paper. One bit high-speed quantize is constructed by differential comparator in FPGA. Time-interleaved digital sampling and buffer encoding are used to one bit stream based on the internal multi-phase clock of FPGA, to achieve sampling rate higher than 1 GHz. High speed digital sampling is realized by the accumulation of one bit sampling data with different comparison levels. An 8 bit, 1.6 GHz ADC based on the proposed method is realized on XC2V3000 Xilinx’s FPGA, which is successfully applied in GPR. The proposed method has the advantages of low cost and power consumption as compared with real sampling, and exhibits higher efficiency as compared with equivalent sampling
Since Mars is far away from Earth, the propagation delay between Mars and Earth is very large. To ensure the effective use of the link transmission bandwidth, China’s first Mars exploration mission has put forward a demand for data compression for all scientific payloads. The on-board mature algorithms for data compression are mainly focused on optical images and microwave imaging radar applications. No articles have been published on data compression methods that are applied to subsurface-penetrating radar. Based on the background of this application, this paper proposes a logarithmic lossy compression algorithm which can meet the mission requirements for high compression ratios of 4:1 and 2.5:1. Its compression error is less than that of the block adaptive quantization (BAQ) algorithm. The algorithm is not only easy to implement on field-programmable gate array (FPGA) platforms, but also offers simple ground decompression and fast imaging. The experimental results show that high compression ratios of 4:1 and 2.5:1 can be realized, even if the data in and between traces do not have a strong correlation. And its relative error is less than 2%, which is a new type of high-efficiency data compression method that can be implemented on-board to meet with the demand of subsurface penetrating radar.