Hybrid nanocomposite films of ITO-coated, self-assembled porous nanostructures of tungsten trioxide (WO3) were fabricated using electrochemical anodization and sputtering. The morphology and chemical nature of the porous nanostructures were studied by Scanning Electron Microscopy (SEM) and X-ray Photoelectron Spectroscopy (XPS), respectively. The photoelectrochemical (PEC) properties of WO3 porous nanostructures were studied in various alkaline electrolytes and compared with those of titania nanotubes. A new type of alkaline electrolyte containing a mixture of NaOH and KOH was proposed for the first time to the best of our knowledge and shown to improve the photocurrent response of the photoanodes. Here, we show that both the WO3 nanostructures and titania nanotubes (used for comparison) exhibit superior photocurrent response in the mixture of NaOH and KOH than in other alkaline electrolytes. The WO3 porous nanostructures suffered from surface corrosion resulting in a huge reduction in the photocurrent density as a function of time in the alkaline electrolytes. However, with a protective coating of ITO (100 nm), the surface corrosion of WO3 porous nanostructures reduced drastically. A tremendous increase in the photocurrent density of as much as 340% was observed after the ITO was applied to the WO3 porous nanostructures. The results suggest that the hybrid ITO/WO3 nanocomposites could be potentially coupled with titania nanotubes in a multi-junction PEC cell to expand the light absorption capability in the solar spectrum for water splitting to generate hydrogen.
Methods for the efficient and affordable remediation of oil spills and chemical leaks are crucially needed in today’s environment. In this study, we have developed a simple, magnetic, porous material based on polydimethylsiloxane (PDMS) and steel wool (SW) that can fulfill these needs. The PDMS-SW presented here is superhydrophobic, superoleophilic, and capable of absorbing and separating oils and organic solvents from water. The material is mechanically and chemically stable, even in salty environments, and can be magnetically guided. It exhibits good selectivity, recyclability, and sorption capacity, and can quickly and continuously absorb and remove large amounts of oils and organic solutions from stationary and turbulent water. In addition, PDMS-SW’s inherently high porosity enables direct, gravity-driven oil-water separation with permeate flux as high as ~32,000 L/m2·h and separation efficiency over 99%. The solution immersion process used to prepare the material is easily scalable and requires only a single step. Thus, with its demonstrated combination of affordability, efficiency, and ease of use, PDMS-SW has the potential to meet the demands of large-area oil and chemical clean-ups.
The outstanding properties of Teflon AF-2400—chemical, optical, etc—inspired us to make modifications to enhance its hydrophobicity. We prepared an AF-2400/indium tin oxide (ITO) nanocomposite by a spin coating technique at room temperature, using the AF-2400 polymer as the matrix and ITO nanoparticles as the filler. Different ITON concentrations ranging from 3 to 30 mg ml −1 were prepared to study the effect of nanoparticle loading on the films’ properties and superhydrophobicity. The effect of spin speed and annealing temperature was also studied. Atomic force microscopy, x-ray photoelectron spectroscopy, and UV–vis analysis were employed to characterize the prepared films. The results indicated that the film’s low surface energy and nano/micro-features made it superhydrophobic. Increasing the ITON concentration to 15 mg ml −1 improved the superhydrophobicity of the composite film by increasing the surface roughness. The coating showed superhydrophobic behavior with a static contact angle (SCA) around 152° and contact angle hysteresis less than 2°. The nanocomposite films also exhibited excellent thermal stability, sustaining temperatures as high as 240 °C without losing their superhydrophobic behavior. Three models, Wenzel, Cassie–Baxter, and Shuttleworth–Bailey, were used to predict the SCA. The results confirmed that the latter model gave the best prediction. In addition to superhydrophobicity, the AF-2400/ITON films coated on a glass substrate showed very high transparency—around 95% in the visible and infrared ranges. An effective medium theory, the Bergman representation, was used to simulate the transmittance of the AF-2400/ITON nanocomposites. The measured and simulated transmittance values were in good agreement in the visible range. Based on our results, this coating may be highly useful for many practical applications, including solar cell coatings, chemical resistance protective coatings, and more.