In order to provide a technical basis for the subsequent concentration and utilization of the tailings treatment process in an iron ore mine, and to achieve the objectives of cost reduction and sustainable development, the settling concentration and settling capacity of a tailings slurry with an initial concentration of 40% in its natural state were tested in conjunction with the pumping supply concentration index of the beneficiation tailings slurry in a metal mine. The test results show that the iron ore tailings particles settle at an overall fast rate: basically, within 10 to 20 min they are able to reach or approach 85 to 99.5% of the final settling state-related index. During the settling process in the fixed container, at first, the clarified water at the top of the tailings slurry is very turbid. With the passage of time, the clarified water gradually becomes blurred and clear from turbidity, and the interface between the slurry and the water gradually becomes clearer. From the phenomena observed during the settling process and the test parameters such as the net increase in clear water and slurry variation, the maximum settling concentration and settling capacity indicators of 50% and 90% can be reached or approached in 5.5 to 7.25 and 10.5 to 15.5 min after settling, and the maximum settling concentration and settling capacity can be reached or approached in 10 to 20 min after the settling process. As the settling tests and observations continued, the relevant settling parameters basically reached the final settling state within the time period of 20 to 1440 min, during which the settling concentration of the tailing sand was 71.33 to 73.42% and the settling capacity was 1.85 to 1.91 g/cm3. It can be judged from the test results that the natural settling of the low concentration tailings slurry can meet the technical specifications required for the filling process, and that the natural settling and concentration of dewatering can save the costs of the relevant facilities and flocculation chemicals, and therefore has good technical and economic feasibility.
29 April 2022 in Mathematical Problems in Engineering
As one of the key measures for comprehensive management of goaf in various mines, filling mining has been recognized by practitioners in recent years due to its functions (e.g., resource utilization of solid waste and thorough goaf treatment). The performance of the filling material is the core challenge of filling mining, and it is influenced by the settling speed, conveying characteristics, and filling body strength. To understand the strength characteristics of a cemented filling body composed of medium-fine tailings, in this study, filling material ratio tests under different content of cement, tailings, and water were conducted. A backpropagation (BP) neural network topology structure was established in this study. The strength after different curing times was used as the output variable to analyze the impact of the cement, tailings, and water content on the filling body. A 3-Hn-3 structural model was employed. When the number of hidden layers Hn was 7, the model achieved the best learning and training effect. The results show that the predicted value, which is close to the measured value (fitting accuracy of 92.43–99.92%; average error of 0.0792–7.5682%), satisfies the engineering requirements. The neural network model can be employed to predict the filling body’s strength and provide a good reference to analyze the change law in the filling body’s strength.
16 September 2023 in Advances in Civil Engineering
Three groups of filling materials with different mix proportions were prepared. PO42.5 grade cement was selected as the binding material, mechanized granular coal gangue and fine sand were used as the filling aggregate, and then the specimens were curing at room temperature and 95% moisture. Through the uniaxial compression test, the influence of gangue–sand ratio, the mass fraction, and curing age on the mechanical properties of filling materials was analyzed. The microstructure analysis of SEM was conducted to explore the internal mechanism of the strength difference of filling materials. The results show that the gangue–sand ratio dramatically influences the uniaxial compressive strength. The strength increases first and then decreases with the gangue–sand ratio increase. The mass fraction of filling paste is positively correlated with specimen strength. When the sand–cement ratio, gangue–sand ratio, and the mass fraction remain unchanged, the longer the curing age, the greater the uniaxial compressive strength of specimens. The specimens with a sand–cement ratio of 3.5 : 1, a gangue–sand ratio of 5 : 5, and a mass fraction of 86% reach the maximum value of 11.03 MPa at a curing age of 10 days. It can be seen that when the gangue–sand ratio is 5 : 5, the filling material has the best mechanical properties, so it can be recommended as the optimal mix proportion for goaf filling. Thus, it provides a solid technical guarantee for the treatment of mine surface collapse disasters and the utilization of bulk coal gangue resources.
In the process of continuous and high-intensity mining in soft rock coal mines, high-quality filling treatment is required for the goaf. A nondestructive acoustic velocimetry method is an excellent way to measure the quality of filling body to effectively maintain the rock stability of the mining area and decrease industrial solid waste. In this study, the gangue and fine sand are used as the filling aggregates, and the uniaxial compression test and acoustic wave test are conducted in the cementitious gangue-sand filling body with different gangue-sand ratio. The results show that the longitudinal wave velocity of the filling body is basically between 1.556 km/s and 2.413 km/s. When the gangue-sand ratio is small, and the slurry concentration is high, the early strength of the cementitious gangue-sand filling body is low, but the later strength has a good growth trend. For specimens with higher strength-filled bodies, the propagation speed of sound waves inside them is also faster, indicating a certain positive correlation between the strength of the filled body and the speed of sound waves. A mathematical equation using longitudinal wave velocity to predict the strength of filling body is established. This equation can be used to predict and judge the quality of the filling body in the mining area.
For the mine of large goaf, there are many factors that affect the filling quality. In order to improve the filling quality, it is necessary to identify the factors that have a significant impact. In this paper, the fuzzy mathematical method was used to analyze the five main factors (PC32.5cement sand ratio, slurry concentration, number of slurry lowering, dehydration and drainage, and tailing particle size grading) affecting the filling quality. The priority of each influence factor was calculated, and the priority set was established. It is found that the slurry launching point and particle size grading of the tailings have an obvious effect on filling quality. After increasing the slurry launching point and optimizing the particle size grading, the strength and uniformity of the filling body are improved.