Vibration induced by marine power devices (MPD) transmitting to the hull structure is one of the most important factors that cause ship vibration and underwater sound radiation. Vibration isolation technologies (VIT) are widely applied to reduce the vibration transmission. However, the overweight issue of VIT for marine power devices is a currently challenging engineering problem. The current reserve of lightweight and high‐efficiency VIT for MPD and relevant theoretical and design research are seriously insufficient. This article first elaborates the causes of the overweight problem of VIT for MPD: (1) failing to grasp the quantitative law; (2) single vibration suppression mechanism. Then, it systematically sorts out the technical methods and application examples with potential to solve the overweight problem, such as dynamic optimization design, lightweight material method, novel intermediate mass structures, distributed dynamic vibration absorbers (DDVAs), locally resonant structures (LRS), particle damping (PD), quasizero stiffness isolators (QZSI), and active vibration control (AVC) technologies. Finally, the future development of lightweight VIT for MPD is prospected. It can be used as a reference for marine vessel vibration attenuation research and engineering design.
Shafting alignment is crucial for marine propulsion systems and may affect the safety and stability of ship operations. Air spring vibration isolation systems (ASVISs) for marine shafting can help control the shafting alignment state by actively adjusting air spring pressures while effectively reducing the mechanical noise. However, how to accurately control the alignment state of marine shafting with air spring vibration isolation system remains a challenge. To address this issue, a digital twin (DT)-driven alignment control method is proposed in this paper. First, we design a digital twin prediction model based on the neural network to describe the data mapping relationship between the air spring pressures and shafting alignment state. Then, based on the prediction model, we transform the shafting alignment control problem into a non-linear optimization problem in which our objective is to minimize the alignment error while balancing the load on different air springs. To obtain the optimal air spring pressures, the genetic algorithm is introduced to solve the optimization problem, fully exploiting its global search capacity. Moreover, in order to achieve the optimized pressures, a soft-constrained controller based on proportional-integral-derivative (PID) algorithm is developed to accurately generate specific control policies based on the monitoring data. Finally, the feasibility and the effectiveness of the proposed alignment control method is verified with a real ASVIS.
19 July 2023 in Journal of Vibration Engineering & Technologies
To suppress the significant vibration line spectra of piping systems under multi-frequency harmonic excitations, a novel dynamic vibration absorber (NDVA) is designed. The NDVA integrates numerous independent resonant units within a finite space through an ingenious structural design and possesses rich frequency regulation characteristics. A vibration model of the piping system equipped with the NDVA is established, and the approximate equivalent parameters of both the piping and the resonant units are inverted based on the frequency response function (FRF) test results. These parameters can be substituted into the model to enhance the accuracy and validity of the theoretical calculations. Based on the relationship between the absorbing bandwidth of the NDVA and the intervals of multi-frequency excitation frequencies, a tailored regulation strategy for different densities of excitation frequencies is proposed. Subsequently, the multi-frequency vibration reduction capability of the NDVA is verified through an example involving dual-frequency harmonic excitations. When there is a notable difference in the intensities of the multi-frequency vibration line spectra, a genetic algorithm is utilized to optimize the mass allocation of the resonant units. Simulation and test results demonstrate that the maximum response amplitude of the optimized system is further reduced.
1 December 2014 in Advances in Mechanical Engineering
To further reduce the vertical stiffness of the air spring, appropriately reduce its lateral stiffness to attenuate the transmission of vibration along the lateral and longitudinal directions, a compound structure air spring (CSAS) was designed. It is a laminated structure with a hard elastic layer at the lower end of the original air spring. Prototypes of the air spring and the CSAS were produced, then related static and dynamic characteristics tests were conducted. Compared with the test results of the air spring, it can be found that under the same air pressure, the bearing capacity of the CSAS is decreased slightly; under rated load, the vertical static/dynamic stiffness and natural frequency is decreased slightly, and the lateral static/dynamic stiffness is decrease significantly. Furthermore, the CSAS was subjected to the safety and reliability tests, and its performance was stable without damage. This article expands the stiffness range of the air spring, and provides a new idea for the design of the air spring with low lateral to vertical stiffness ratio and low natural frequency.
In order to improve the alignment stability of the air vibration isolation device of a high-powered main engine, we established a mechanical model for the air vibration isolation system and analyzed the alignment deviation of the device and the vibration decoupling conditions of the system. Additionally, an optimized design method for the dual-direction support of the air vibration isolators positioned symmetrically on the main engine was proposed. The resultant design showed that when compared to the conventional inclined support of air springs for the main engines onboard ships, the dual-direction support design proposed in this paper for air vibration isolation could eliminate the adverse effect of the output torque reaction on the alignment of the main engine and decouple the system to reduce the number of peaks in the frequency response of vertical force transmission. The optimized design could effectively improve the alignment performance of the device for tilted or swinging operating conditions and maintain the good alignment stability of the device when a single vertical support air spring fails. A single vertical support air spring failure mainly affects the stability of the main engine under the reaction of the output torque, especially the air springs arranged in the corner, while the air springs arranged in the middle have no effect. The optimized design could also improve the vibration isolation performance. This is important for the design of air spring vibration isolation devices for high power density main engines.