We report a controllable and scalable fabrication approach for the superhydrophobic hierarchical structures and demonstrate the excellent ability to harvest water energy when applied to water-solid contact triboelectric nanogenerator (TENG). A strategy combined with multiple photolithography and micromolding process was developed to accurately regulate the diameters and the center distances of the two-level micropillars. A variety of hierarchical structures were successfully fabricated and presented the advantages of structure control, large scale, high accuracy, and high consistency. The hydrophobic property characterizations were conducted, and the results indicated that the hierarchical structures showed a larger contact angle than the single-level structures and achieved superhydrophobicity. Then the hierarchical structures were applied to water-TENGs with flowing water continuously dripping on, and the effect of the structure parameter on the triboelectric output was analyzed. The hierarchical structures exhibited a superior ability to harvest water energy than the flat film and the single-level structures due to the enhanced friction area and superhydrophobic property. At a flowing velocity of 8 mL/s, the hierarchical structure generated the output voltage of approximately 34 V and the short-circuit current of around 5 μA. The water-TENG device exhibited a power density peak of 7.56 μW/cm2 with a resistive load of 16.6 MΩ at a flowing velocity of 10 mL/s. These findings shed light on the potential applications of the hierarchical structures-based water-TENGs to water energy harvesting and self-powered sensor devices.
Axial-grooved gas-lubricated journal bearings have been widely applied to precision instrument due to their high accuracy, low friction, low noise and high stability. The rotor system with axial-grooved gas-lubricated journal bearing support is a typical nonlinear dynamic system. The nonlinear analysis measures have to be adopted to analyze the behaviors of the axial-grooved gas-lubricated journal bearing-rotor nonlinear system as the linear analysis measures fail. The bifurcation and chaos of nonlinear rotor system with three axial-grooved gas-lubricated journal bearing support are investigated by nonlinear dynamics theory. A time-dependent mathematical model is established to describe the pressure distribution in the axial-grooved compressible gas-lubricated journal bearing. The time-dependent compressible gas-lubricated Reynolds equation is solved by the differential transformation method. The gyroscopic effect of the rotor supported by gas-lubricated journal bearing with three axial grooves is taken into consideration in the model of the system, and the dynamic equation of motion is calculated by the modified Wilson-θ-based method. To analyze the unbalanced responses of the rotor system supported by finite length gas-lubricated journal bearings, such as bifurcation and chaos, the bifurcation diagram, the orbit diagram, the Poincaré map, the time series and the frequency spectrum are employed. The numerical results reveal that the nonlinear gas film forces have a significant influence on the stability of rotor system and there are the rich nonlinear phenomena, such as the periodic, period-doubling, quasi-periodic, period-4 and chaotic motion, and so on. The proposed models and numerical results can provide a theoretical direction to the design of axial-grooved gas-lubricated journal bearing-rotor system.
23 November 2017 in Science China Technological Sciences
Template‐based methods are a commonly used way to prepare superhydrophobic surfaces, in which, one of the critical issues, is template fabrication. In this work, a template with a dual‐scale hierarchical structures fabrication method is investigated, in which, using the Cr and photoresist as etching mask, the fused silica glass substrate is etched in a buffered hydrofluoric solution. Optical photos and atomic force microscopy (AFM) scans show that the excellent ordered and uniform microstructures with a feature size less than 4 μm combining with the nanostructures with a feature size of about 20–30 nm on the etched surface have been fabricated, indicating hierarchical structures being obtained. Then the template with dual‐scale structures is used as a master template and experiments of pattern transferring to PDMS and photoresist by cast moulding and by imprint lithography, respectively, have been conducted. The duplicating fidelity is characterised through optical photos and AFM scans. The contact angles of water on various fabricated surfaces are characterised and the influence of the surface roughness on wettability has been discussed.